Retour: Accueil
MyLaserTools.com
Toutes les catégories

Fête des Pères5 outils

Des cadeaux découpés au laser pour la fête des Pères. Fabriquez un pied à coulisse ou une équerre fonctionnels pour l'atelier, un book nook de garage ou d'atelier de menuiserie, une moto miniature ou un porte-bouteilles à son nom.

Gratuit
Générateur de règles example
Découpe laserCNC

Générateur de règles

Générateur gratuit de règles de précision pour la découpe laser. Créez des outils de mesure personnalisés avec des graduations précises

Gratuit
Générateur de porte-clés plaque fantaisie example
Découpe laserImpression 3DCNC

Générateur de porte-clés plaque fantaisie

Créateur gratuit de porte-clés en forme de plaque d'immatriculation fantaisie avec anneau de suspension et texte personnalisé. Téléchargez un SVG pour la découpe laser ou un STL/3MF pour l'impression 3D. Usage fantaisie uniquement.

Gratuit
Générateur de cadrans d'horloge example
Découpe laserImpression 3DCNC

Générateur de cadrans d'horloge

Générateur gratuit de cadrans d'horloge en SVG pour la découpe laser. Créez des cadrans personnalisés ronds ou carrés, avec chiffres arabes ou romains et graduations précises

Gratuit
Générateur de médailles example
Découpe laserImpression 3DCNC

Générateur de médailles

Générateur gratuit de médailles personnalisées avec texte courbé, texte central et pictogrammes

Gratuit
Générateur de chevalets de bureau example
Découpe laserImpression 3DCNC

Générateur de chevalets de bureau

Porte-étiquette de bureau gratuit en chevalet, avec faces à graver pour plaques nominatives et panneaux de table, personnalisable dans l'éditeur.

Joiner's Bench
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Joiner's Bench

A miniature for book nooks and dioramas. Joiner's bench: a miniature traditional woodworking bench for dioramas, book nooks and a woodworker's shelf. Two end frames (a leg front and back, a rail at the top, a stretcher low down) with two long stretchers through the legs, the top in two glued layers with the legs' tenons showing through it, and the face vise hung from the top's front on a tab with its handle engraved on the face. A half-built chair, the plane with its shaving and a mug of coffee can stand on the top. Assembly: slide the long stretchers into the end frames, glue the two layers o

Workbench
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Workbench

A miniature for book nooks and dioramas. Workbench: a miniature workshop bench for dioramas, garages and book nooks. Two end frames (legs, a top rail and a shelf band, each one piece) hold a slatted shelf and a front and a back apron between them, and lock into a butcher-block top. A vise, a radio and a mug can stand in slots on the top. Assembly: push the shelf and the aprons into one end frame, add the other, press the top onto the frames' tabs, stand the things on top.

Motorcycle on a Lift
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Motorcycle on a Lift

A miniature for book nooks and dioramas. Motorcycle on a lift: a vintage café racer for dioramas, garages and book nooks, standing on a scissor lift table. The bike is a layered profile: the body (front wheel, fork, frame, engine, seat, exhaust, and a paddock stand under the swingarm, because its rear wheel is off for repair) is one piece standing in two slots in the lift's top; the tank and the engine covers are glued on both faces for depth, and the handlebar crosses the riser in a halving joint. The rear wheel stands in its own slot beside it. The lift is a top plate on two one-piece scisso

Model Car Display Cabinet
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Model Car Display Cabinet

A miniature for book nooks and dioramas. Three-shelf model display with two doors and five layered racers. Car 07 is on the workbench. Its numbered tag takes the empty bay.

The Wood Shed Book Nook
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

The Wood Shed Book Nook

Woodworker book nook: "The Wood Shed". Saturday morning, sun through the dust. A chair half built stands at the vise end of the bench, the plane beside it with its shaving still curling out, the coffee going cold. Boards lie stacked on the lumber rack along the wall, a board rests across the sawhorses with a pencil mark for the saw, and clamps hang on their rail. The note by the window says "measure twice". A finger-jointed shell with barn-board posts holds real miniature furniture in detail ply: the joiner's bench (two end frames, two long stretchers through the legs, the top in two glued lay

Night Shift Garage Book Nook
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Night Shift Garage Book Nook

Garage book nook: "Night Shift". Twenty to four in the morning. A vintage motorcycle stands on the lift table, half repaired: its rear wheel is off and stands beside it, the bike rests on a paddock stand. The radio on the bench is still playing; the coffee beside it went cold hours ago. On the wall the calendar has tomorrow circled: PICK UP 6AM. A finger-jointed shell with hazard-striped door posts holds real miniature furniture in detail ply: the motorcycle (a layered profile with tank and engine covers on both faces and a handlebar halved across the riser) on a scissor lift table, a workbenc

Vernier Caliper
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Vernier Caliper

Vernier caliper: a working sliding caliper that reads to a tenth of a millimetre and to 1/128 inch. The main scales are scored along the beam and seen through a window in the slider, whose vernier scales sit right against them. Outside jaws below, inside jaws above. How to read it: the slider's 0 gives whole millimetres on the beam; the vernier line that meets a beam line exactly gives the tenths. Assembly: slide the slider plates over the beam with the spacers above and below it, then rivet or pin them through the holes. Cut it from acrylic or a stable plywood for the best accuracy.

Six-Pack Carrier
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Six-Pack Carrier

Six-pack carrier: two rings hold the bottles apart so they never clink, a tall spine with a hand hole carries the load, and the end plates are screwed on with captive nuts, so it comes apart flat. The spine is screwed to both end plates and the end plates to the base, so the weight of the bottles hangs on screws, never on a push fit. Set the bottle size and how many in a row; the rings and handle follow. Assembly: slide both rings up the spine from below and plug the spine's tabs into the base. Fit the end plates over the tabs of the base, the rings and the spine, then screw them on: a nut dro

L-Square
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

L-Square

L-square: a try square for marking and measuring, with scales along both arms that start from the inside of the stock, so the zero sits on the board's edge. The stock is three layers thick and hooks over the edge; the blade is one. A row of pencil holes along the blade marks lines parallel to the edge, and a 45° face on the stock marks mitres. Choose millimetres or inches. Assembly: glue a stock layer on each face of the square's short arm, lining up the inside edges exactly. Check it against a known square.

Horn Phone Stand
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Horn Phone Stand

Horn phone stand: a solid block of layers that holds a phone at a lean and carries the sound of its speaker forward through a horn inside the block, flaring out to the front. The slot leans because each layer's cut steps back a little from the one below; the horn is cut through the layers under the slot. The front steps down so the screen stays clear. Assembly: glue the layers in order, base first, lining up the backs.

Desk Catapult
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Desk Catapult

Catapult: a desk mangonel. A three-layer laminated arm turns on a dowel axle between two braced uprights, sprung by rubber bands from a notch on its short end to an anchor dowel behind. Pull the arm back and push the trigger peg across over it; pull the peg out sideways to throw. The arm hits the padded stop bar and the ball flies on. The peg stays in the right upright when pulled, so it cannot get lost. Assembly: glue the three arm layers into one, with the tabbed layer in the middle, and glue the cup and its ring onto the tabs. Push the uprights' tabs into the base, fit the stop bar and the

Engraved ruler
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Engraved ruler

A ruler with scored millimetre ticks and engraved numbers.

Actualités par e-mail

Suivez les nouveautés de MyLaserTools.

Envoyez-moi des e-mails sur les nouveaux outils, les mises à jour, les tutoriels et les offres occasionnelles de MyLaserTools. Désinscription possible à tout moment.

MyLaserTools
par YXE Creations Craft Hub
Des centaines de créateurs à travers le monde nous font confiance
Identifiez-nous sur Instagram
Partagez vos réalisations avec @mylasertools
Rejoignez notre groupe Facebook
Partagez vos créations, posez vos questions et trouvez l'inspiration
YXE Creations Craft Hub Inc

© 2026 MyLaserTools.com. Tous droits réservés.