Back: Community
MyLaserTools.com

Pipe Saddle Clamps

One-hole and two-hole straps that hold pipes, conduit, tubing, dowels and LED profiles to a wall or bench. Print one size, or a run of common sizes from 6 mm…

by Hardware Designs

Settings

Clamp

Style
Clamp style
Pipe
Pipe diameter in mm
Assortment
Print a run of sizes from small to this pipe size
Fit
Extra room around the pipe in mm

Strap

Width
Strap width in mm
Thickness
Strap thickness in mm
Screw
Screw hole diameter in mm

Print

Count
Clamps of each size

3D Preview

Building your model
Inspirational Palette

Code

Copy to Workbench

Photos

Pipe Saddle Clamps

About this design

Written in OpenSCAD · 3D print

One-hole and two-hole straps that hold pipes, conduit, tubing, dowels and LED profiles to a wall or bench. Print one size, or a run of common sizes from 6 mm up to the size you set.

Prints on its side, so the layers wrap around the pipe and the strap does not split along the arch.

3D Print ExclusiveHardware
pipe clampconduitstraphose

Personal useCommercial use

What does this mean?

How to make it

  1. 1Change the settings. The preview updates after each change.
  2. 2Download STL for any slicer, or 3MF to keep the coloured parts apart.
  3. 3Like the design and add a photo of what you made below.

Questions

Yes. It is free to download and use under its licence.

Yes. Change the settings on this page and the preview updates as you go. When it looks right, download the file.

STL for any slicer, and 3MF with each coloured part kept as its own object.

The size follows the settings on this page, and the size box under the preview shows the result.

Yes. The licence covers personal and commercial use of the pieces you make.

Made by the community

Cut this one? Share a photo and a note about how it went and get 10 sparks right away.

I made this

More from Hardware Designs

Crank Handle
CustomizableFree
3D print
by Hardware Designs

Crank Handle

A hand crank with a square, hex, round or D bore and a grip that spins on its pin. For awning winders, pasta rollers, window cranks, winches and anything with an adjusting screw. The arm prints flat and the grip prints upright, then snaps onto the pin. A pointed set screw hole holds it on the shaft.

Flanged and Cap Nuts
CustomizableFree
3D print
by Hardware Designs

Flanged and Cap Nuts

Printed hex nuts with a washer flange that spreads the load on wood and plastic, or a domed cap that covers the sharp end of the bolt. Metric and UNC sizes, with a clearance setting so the thread suits your printer. Prints upright with no supports, several at once.

Lever Handle Nut
CustomizableFree
3D print
by Hardware Designs

Lever Handle Nut

A clamping lever for router fences, drill press tables, tool rests and camera rigs, where a round knob slips in your hand. Straight, cranked or paddle lever, 35 to 140 mm long. Use a printed thread, a pocket for a steel nut, or a bolt head pocket. Prints flat with no supports.

Wing and Thumb Nuts
CustomizableFree
3D print
by Hardware Designs

Wing and Thumb Nuts

Hand-tightened nuts for M5 to M12 and 1/4 to 1/2 inch bolts, in wing, big wing, knurled, star and lobed shapes. Pick a printed thread, a pocket that grips a steel nut, or a pocket for a bolt head to turn it into a thumb screw. Prints upright with no supports. Printed threads hold best from M6 and 1/4 inch up; below that use the steel nut pocket.

Similar designs

Turnbuckle
CustomizableFree
3D print
by Hardware Designs

Turnbuckle

A fully printed turnbuckle with one right-hand and one left-hand eye bolt. Turning the body draws both eyes in, for tightening garden wire, shade sails, banner lines and display rigging. The left-hand eye has a notch and the left-hand end of the body has a groove, so you can tell them apart. All three parts print upright with no supports.

Strap Slides and Line Tensioners
CustomizableFree
3D print
by Hardware Designs

Strap Slides and Line Tensioners

Tri-glide adjusters, strap keepers and D-rings for 10 to 50 mm webbing, plus three-hole tensioners for tent guy lines and clotheslines. Everything prints flat with no supports, a sheet at a time.

Rope Cleat
CustomizableFree
3D print
by Hardware Designs

Rope Cleat

A horn cleat for tying off flag lines, blind cords, tarps, hammocks and garden netting with a quick figure-eight. Set the length, rope size and width, and bolt it down through both posts. Prints upright with no supports. The horns rise at 45 degrees.

Tie-Down Ring
CustomizableFree
3D print
by Hardware Designs

Tie-Down Ring

A folding D-ring anchor for truck beds, trailers, crates, garden netting and gym straps. The ring comes off the bed already trapped under its strap, and folds flat when you are not using it. Prints flat in place with no supports. Screw down both pads.