Volver: Inicio
MyLaserTools.com
Todas las categorías

Día del Padre5 herramientas

Regalos para el Día del Padre cortados con láser. Haz un calibre o una escuadra que funcionan de verdad para el taller, un book nook de garaje o de carpintería, una moto en miniatura o un portabotellas con su nombre.

Gratis
Generador de reglas example
Corte láserCNC

Generador de reglas

Generador gratuito de reglas de precisión para corte láser. Cree herramientas de medición personalizadas con medidas exactas

Gratis
Generador de colgantes de matrícula example
Corte láserImpresión 3DCNC

Generador de colgantes de matrícula

Creador gratuito de llaveros con matrícula decorativa con anilla colgante y texto personalizado. Descarga SVG para corte láser o STL/3MF para impresión 3D. Solo para uso decorativo.

Gratis
Generador de esferas de reloj example
Corte láserImpresión 3DCNC

Generador de esferas de reloj

Generador gratuito de archivos SVG para crear diseños de esferas de reloj, ideal para el corte con láser. Cree diseños personalizados de esferas de reloj con formas circulares o cuadradas, números arábigos o romanos y marcas de tiempo precisas

Gratis
Generador de medallas example
Corte láserImpresión 3DCNC

Generador de medallas

Generador gratuito de medallas personalizadas con texto curvo, texto central y pictogramas

Gratis
Generador de letreros de escritorio example
Corte láserImpresión 3DCNC

Generador de letreros de escritorio

Soporte gratuito de letreros de escritorio en forma de A con caras grabables para placas de nombre y letreros de mesa, personalizables en el editor.

Joiner's Bench
PersonalizableGratis
Corte láserImpresión 3D
por Kerf Designs

Joiner's Bench

A miniature for book nooks and dioramas. Joiner's bench: a miniature traditional woodworking bench for dioramas, book nooks and a woodworker's shelf. Two end frames (a leg front and back, a rail at the top, a stretcher low down) with two long stretchers through the legs, the top in two glued layers with the legs' tenons showing through it, and the face vise hung from the top's front on a tab with its handle engraved on the face. A half-built chair, the plane with its shaving and a mug of coffee can stand on the top. Assembly: slide the long stretchers into the end frames, glue the two layers o

Workbench
PersonalizableGratis
Corte láserImpresión 3D
por Kerf Designs

Workbench

A miniature for book nooks and dioramas. Workbench: a miniature workshop bench for dioramas, garages and book nooks. Two end frames (legs, a top rail and a shelf band, each one piece) hold a slatted shelf and a front and a back apron between them, and lock into a butcher-block top. A vise, a radio and a mug can stand in slots on the top. Assembly: push the shelf and the aprons into one end frame, add the other, press the top onto the frames' tabs, stand the things on top.

Motorcycle on a Lift
PersonalizableGratis
Corte láserImpresión 3D
por Kerf Designs

Motorcycle on a Lift

A miniature for book nooks and dioramas. Motorcycle on a lift: a vintage café racer for dioramas, garages and book nooks, standing on a scissor lift table. The bike is a layered profile: the body (front wheel, fork, frame, engine, seat, exhaust, and a paddock stand under the swingarm, because its rear wheel is off for repair) is one piece standing in two slots in the lift's top; the tank and the engine covers are glued on both faces for depth, and the handlebar crosses the riser in a halving joint. The rear wheel stands in its own slot beside it. The lift is a top plate on two one-piece scisso

Model Car Display Cabinet
PersonalizableGratis
Corte láserImpresión 3D
por Kerf Designs

Model Car Display Cabinet

A miniature for book nooks and dioramas. Three-shelf model display with two doors and five layered racers. Car 07 is on the workbench. Its numbered tag takes the empty bay.

The Wood Shed Book Nook
PersonalizableGratis
Corte láserImpresión 3D
por Kerf Designs

The Wood Shed Book Nook

Woodworker book nook: "The Wood Shed". Saturday morning, sun through the dust. A chair half built stands at the vise end of the bench, the plane beside it with its shaving still curling out, the coffee going cold. Boards lie stacked on the lumber rack along the wall, a board rests across the sawhorses with a pencil mark for the saw, and clamps hang on their rail. The note by the window says "measure twice". A finger-jointed shell with barn-board posts holds real miniature furniture in detail ply: the joiner's bench (two end frames, two long stretchers through the legs, the top in two glued lay

Night Shift Garage Book Nook
PersonalizableGratis
Corte láserImpresión 3D
por Kerf Designs

Night Shift Garage Book Nook

Garage book nook: "Night Shift". Twenty to four in the morning. A vintage motorcycle stands on the lift table, half repaired: its rear wheel is off and stands beside it, the bike rests on a paddock stand. The radio on the bench is still playing; the coffee beside it went cold hours ago. On the wall the calendar has tomorrow circled: PICK UP 6AM. A finger-jointed shell with hazard-striped door posts holds real miniature furniture in detail ply: the motorcycle (a layered profile with tank and engine covers on both faces and a handlebar halved across the riser) on a scissor lift table, a workbenc

Vernier Caliper
PersonalizableGratis
Corte láserImpresión 3D
por Kerf Designs

Vernier Caliper

Vernier caliper: a working sliding caliper that reads to a tenth of a millimetre and to 1/128 inch. The main scales are scored along the beam and seen through a window in the slider, whose vernier scales sit right against them. Outside jaws below, inside jaws above. How to read it: the slider's 0 gives whole millimetres on the beam; the vernier line that meets a beam line exactly gives the tenths. Assembly: slide the slider plates over the beam with the spacers above and below it, then rivet or pin them through the holes. Cut it from acrylic or a stable plywood for the best accuracy.

Six-Pack Carrier
PersonalizableGratis
Corte láserImpresión 3D
por Kerf Designs

Six-Pack Carrier

Six-pack carrier: two rings hold the bottles apart so they never clink, a tall spine with a hand hole carries the load, and the end plates are screwed on with captive nuts, so it comes apart flat. The spine is screwed to both end plates and the end plates to the base, so the weight of the bottles hangs on screws, never on a push fit. Set the bottle size and how many in a row; the rings and handle follow. Assembly: slide both rings up the spine from below and plug the spine's tabs into the base. Fit the end plates over the tabs of the base, the rings and the spine, then screw them on: a nut dro

L-Square
PersonalizableGratis
Corte láserImpresión 3D
por Kerf Designs

L-Square

L-square: a try square for marking and measuring, with scales along both arms that start from the inside of the stock, so the zero sits on the board's edge. The stock is three layers thick and hooks over the edge; the blade is one. A row of pencil holes along the blade marks lines parallel to the edge, and a 45° face on the stock marks mitres. Choose millimetres or inches. Assembly: glue a stock layer on each face of the square's short arm, lining up the inside edges exactly. Check it against a known square.

Horn Phone Stand
PersonalizableGratis
Corte láserImpresión 3D
por Kerf Designs

Horn Phone Stand

Horn phone stand: a solid block of layers that holds a phone at a lean and carries the sound of its speaker forward through a horn inside the block, flaring out to the front. The slot leans because each layer's cut steps back a little from the one below; the horn is cut through the layers under the slot. The front steps down so the screen stays clear. Assembly: glue the layers in order, base first, lining up the backs.

Desk Catapult
PersonalizableGratis
Corte láserImpresión 3D
por Kerf Designs

Desk Catapult

Catapult: a desk mangonel. A three-layer laminated arm turns on a dowel axle between two braced uprights, sprung by rubber bands from a notch on its short end to an anchor dowel behind. Pull the arm back and push the trigger peg across over it; pull the peg out sideways to throw. The arm hits the padded stop bar and the ball flies on. The peg stays in the right upright when pulled, so it cannot get lost. Assembly: glue the three arm layers into one, with the tabbed layer in the middle, and glue the cup and its ring onto the tabs. Push the uprights' tabs into the base, fit the stop bar and the

Engraved ruler
PersonalizableGratis
Corte láserImpresión 3D
por Kerf Designs

Engraved ruler

A ruler with scored millimetre ticks and engraved numbers.

Actualizaciones por correo

Mantente al día con MyLaserTools.

Quiero recibir correos sobre nuevas herramientas, actualizaciones del producto, tutoriales y ofertas ocasionales de MyLaserTools. Puedo darme de baja en cualquier momento.

MyLaserTools
por YXE Creations Craft Hub
Cuenta con la confianza de cientos de creadores en todo el mundo
Etiquétenos en Instagram
Comparte lo que has creado con @mylasertools
Únete a nuestro grupo de Facebook
Comparte tus creaciones, haz preguntas, inspírate
YXE Creations Craft Hub Inc

© 2026 MyLaserTools.com. Todos los derechos reservados.