Indietro: Home
MyLaserTools.com
Tutte le Categorie

Halloween4 strumenti

Generatori gratuiti di SVG per il taglio laser di Halloween. Crea etichette con nomi di zucche, etichette regalo personalizzate e decorazioni stagionali paurose.

Gratis
Etichetta Nome Zucca example
Taglio laserCNC

Etichetta Nome Zucca

Crea un SVG gratuito di etichetta nome zucca perfetto per Halloween e progetti autunnali

Gratis
Generatore di Etichette Regalo example
Taglio laserStampa 3DCNC

Generatore di Etichette Regalo

Generatore gratuito di belle etichette regalo personalizzate con testo e pittogrammi personalizzati

Gratis
Stencilify example
Taglio laserStampa 3DCNC

Stencilify

Generatore gratuito di stencil per taglio laser e stampa 3D. Perfetto per progetti fai da te

Pro
Map Designer example
Taglio laserStampa 3DCNCStampa

Map Designer

Creatore online di mappe per il laser con file di taglio SVG a livelli. Trasforma città, laghi, coste e montagne in livelli personalizzabili di strade, acqua, rilievo e cornice, poi esporta SVG separati o un unico SVG combinato.

Vampire Coffin
PersonalizzabileGratis
Taglio laserStampa 3D
di Kerf Designs

Vampire Coffin

A miniature for book nooks and dioramas. Coffin: a miniature vampire's coffin for dioramas, Halloween and book nooks. A true coffin shape from every side: a stack of coffin-shaped rings on a solid floor, aligned by two keys that stand in the floor's slots and slide through notches in every ring; no corner joints to show. The lid is two layers, closed or slid half open on the velvet and the rose inside. It can stand on a stone plinth. Assembly: stand the keys in the floor, thread the rings down over them, glue each, lay the lid on; set it all on the plinth.

Spell-Book Stand
PersonalizzabileGratis
Taglio laserStampa 3D
di Kerf Designs

Spell-Book Stand

A miniature for book nooks and dioramas. Spell-book stand: a miniature lectern for dioramas, libraries and book nooks. Two shaped sides hold a sloping book rest and a low shelf, both tabbed into slots in the sides; the rest sits a lip below the sides' top edges, which keep the book from sliding off. An open book with a ribbon is engraved on the rest, and a row of books can stand on the shelf. Assembly: push the shelf and the rest into one side, add the other side, stand the books in their slots.

The Count's Marked Atlas
PersonalizzabileGratis
Taglio laserStampa 3D
di Kerf Designs

The Count's Marked Atlas

A miniature for book nooks and dioramas. One open atlas, its inclined cradle and three removable brass pins. Seat the keyed rail between the two sides, then lower the desk onto the four angled tabs. Glue both pages to the cover. The three 1.5 x 4.6 mm brass pins enter the map and cover and stop on the desk top.

Victor's Anatomy Table
PersonalizzabileGratis
Taglio laserStampa 3D
di Kerf Designs

Victor's Anatomy Table

A miniature for book nooks and dioramas. Glue the stretchers between the two cheeks. Glue the two deck pieces and seat the moving rails on the deck's underside with the bores aligned. Slide 2 mm brass rod through both cheeks and the two pivot bores. The longer aft rod locks the pitch. Pull it to tip the deck to the other position, then insert it through both cheeks and the newly aligned bores.

Brewing Hours Witch House Book Nook
PersonalizzabileGratis
Taglio laserStampa 3D
di Kerf Designs

Brewing Hours Witch House Book Nook

Witch house book nook: "Brewing Hours". Midnight, full moon over the crooked forest. The cauldron is bubbling on the hearth, a spell book lies open on its stand, herbs hang drying from the beams. Someone knocked a potion off the shelf: the jar lies in a green puddle, and a trail of paw prints leads from it to behind the cauldron, where the cat is hiding. A finger-jointed shell with a crooked timber-framed front holds real miniature furniture in detail ply: a stone fireplace (front, sides and a soot-black back under a timber mantel, a fire inside), a cauldron of two cross-lapped profiles with i

The Laboratory Book Nook
PersonalizzabileGratis
Taglio laserStampa 3D
di Kerf Designs

The Laboratory Book Nook

Ingolstadt. The rain persists after Victor has left his workshop. The brass pins run through both cheeks and both rails. To remove the table, shift it about 7 mm toward the aisle, lift it over the front sill and slide it forward. Draw the aft pin only once the table is outside.

The Count's Library Book Nook
PersonalizzabileGratis
Taglio laserStampa 3D
di Kerf Designs

The Count's Library Book Nook

Harker has stepped away from the Count's open atlas. Glue the map and index pages to the cover and let the book rest on the desk lip. Drop three 1.5 x 4.6 mm brass pins into the aligned bores.

Coffin Keepsake Box
PersonalizzabileGratis
Taglio laserStampa 3D
di Kerf Designs

Coffin Keepsake Box

Coffin box: a keepsake box in the classic six-sided coffin shape, built up from stacked rings so the angled corners need no joints. The lid has a scored border and an engraved name, and a plate under it drops into the top ring to hold it in place. Assembly: glue the rings onto the base one at a time, lining up their edges, and sand the sides smooth. Glue the plate under the lid.

Aggiornamenti via email

Resta aggiornato su MyLaserTools.

Inviami email su nuovi strumenti, aggiornamenti del prodotto, tutorial e occasionali offerte MyLaserTools. Puoi annullare l'iscrizione in qualsiasi momento.

MyLaserTools
di YXE Creations Craft Hub
Fidato da centinaia di maker in tutto il mondo
Taggaci su Instagram
Condividi quello che hai fatto con @mylasertools
Unisciti al nostro Gruppo Facebook
Condividi creazioni, fai domande, lasciati ispirare
YXE Creations Craft Hub Inc

© 2026 MyLaserTools.com. Tutti i diritti riservati.