Retour: Communauté
MyLaserTools.com

Folding Bed Tray

Bed tray: a breakfast tray with legs that fold flat under it. Each end has a pair of legs joined by a stretcher, pivoting on a dowel through lugs tabbed under…

par Kerf Designs

Réglages

Unités

Tray

Length
Length
Width
Width
Wall
Height of the walls
Height
Height of the tray's base above the bed, legs open
Message
Message on the base; leave empty for none

Assembled view

Folded
Legs folded flat under the tray

Material

Épaisseur du matériau
La plaque que vous découpez. Les fentes et les tenons s'y adaptent.
mm
Largeur de coupe
Largeur de matériau brûlée par le laser.
mm
Axle
Dowel the legs turn on
Sheet
Your laser's sheet size; the base needs one longer than the tray

Aperçu 3D

Génération de votre modèle
Palette d'inspiration

Code

Copier dans l'atelier

Photos

Folding Bed Tray

À propos de cette création

Découpe laser et Impression 3D

Bed tray: a breakfast tray with legs that fold flat under it. Each end has a pair of legs joined by a stretcher, pivoting on a dowel through lugs tabbed under the base. Opened, the legs swing a few degrees past upright onto a stop above the pivot, so weight on the tray presses them harder against it and they cannot fold under load; pulled inwards they fold flat under the base, the two ends clear of each other. The tray has finger-jointed walls, hand holes in its ends and a message engraved on the base. Assembly: fit the walls into the base, the long walls first. Push the lugs' tabs into the ba

CadeauxDécoration intérieureFête des Mères
home decorgifts

Usage personnelUsage commercial

Qu'est-ce que cela signifie ?

Comment la fabriquer

  1. 1Modifiez les réglages. L'aperçu se met à jour après chaque modification.
  2. 2Téléchargez le SVG pour votre laser, ou ouvrez-le dans l'éditeur de créations pour le compléter.
  3. 3Aimez la création et ajoutez ci-dessous une photo de votre réalisation.

Questions

Oui. Vous pouvez la télécharger et l'utiliser gratuitement selon sa licence.

Oui. Modifiez les réglages sur cette page : l'aperçu se met à jour au fur et à mesure. Quand le résultat vous convient, téléchargez le fichier.

Un SVG pour votre logiciel laser. Vous pouvez aussi l'ouvrir dans l'éditeur de créations, ou télécharger des fichiers STL et 3MF à l'épaisseur du matériau pour imprimer les pièces.

La taille suit les réglages de cette page, et l'encadré de taille sous l'aperçu affiche le résultat.

Réglez l'épaisseur du matériau sur celle de la plaque que vous découpez. Les fentes et les tenons s'y adaptent.

Oui. La licence couvre l'usage personnel et commercial des objets que vous fabriquez.

Réalisé par la communauté

Vous avez découpé cette création ? Partagez une photo et une note sur votre expérience pour recevoir immédiatement 10 étincelles.

Je l'ai réalisé

Plus de créations de Kerf Designs

Locker Stall
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Locker Stall

A miniature for book nooks and dioramas. Locker stall: a miniature team locker with the player's jersey, for dioramas, shelves and a gift to any player. Two sides hold the back, a kick panel, a bench seat, a helmet shelf and a name board, all tabbed in; the jersey (team colours, name, number) hangs by a hole in its hanger on a peg tabbed into the back. Skates or cleats can stand on the seat, the helmet on the shelf. Hockey, soccer, basketball or baseball. Assembly: push the back, the kick panel, the seat, the shelf and the name board into one side, add the other, push the peg into the back, ha

Vampire Coffin
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Vampire Coffin

A miniature for book nooks and dioramas. Coffin: a miniature vampire's coffin for dioramas, Halloween and book nooks. A true coffin shape from every side: a stack of coffin-shaped rings on a solid floor, aligned by two keys that stand in the floor's slots and slide through notches in every ring; no corner joints to show. The lid is two layers, closed or slid half open on the velvet and the rose inside. It can stand on a stone plinth. Assembly: stand the keys in the floor, thread the rings down over them, glue each, lay the lid on; set it all on the plinth.

Library Bookcase
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Library Bookcase

A miniature for book nooks and dioramas. Library bookcase: a miniature bookcase with its rolling-style ladder, for dioramas, dollhouses and book nooks. The bookcase is a tab-and-slot box of sides, a back, shelves and a top, with rows of books standing in slots on every shelf and, with the ladder, a brass rail tabbed across the front. The ladder's two rails lean back to that rail and hook over it through notches in their tops; its treads tab into the rails and its feet stand in the base. One book on the top shelf has a ribbon bookmark with an initial on it. Assembly: build the bookcase and stan

Bread Rack
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Bread Rack

A miniature for book nooks and dioramas. Bread rack: a miniature bakery rack for dioramas, shop fronts and book nooks. Two ladder ends (legs, a band at every shelf, cut-outs between) hold slatted shelves tabbed into them, and the bread stands in slots on the shelves: round loaves, croissants, and baguettes in a basket on top. Assembly: push the shelves into one ladder end, add the other, stand the bread in its slots, set the feet in the base.

Créations similaires

Tile Keychain
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Tile Keychain

Tile keychain: a word spelled in letter tiles, all on one keychain. Each tile has its letter engraved large and its place in the alphabet small in the corner. The tiles sit side by side on a walnut back with a thin line of walnut showing between them, and the back carries the ring tab, so the word stays together and strong. Without the back it cuts as one piece with each tile scored round. Assembly: glue the tiles onto the back in order, lining them up with the scored marks, and thread a split ring through the tab.

Luggage Tag
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Luggage Tag

Luggage tag: a name and two lines of address engraved on a rounded tag, with a strap slot at the top. The hole and the slot come from a module that takes the tag as its children(), so the same module fits any shape. Finishing: thread a leather strap or a cable tie through the slot.

Six-Pack Carrier
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Six-Pack Carrier

Six-pack carrier: two rings hold the bottles apart so they never clink, a tall spine with a hand hole carries the load, and the end plates are screwed on with captive nuts, so it comes apart flat. The spine is screwed to both end plates and the end plates to the base, so the weight of the bottles hangs on screws, never on a push fit. Set the bottle size and how many in a row; the rings and handle follow. Assembly: slide both rings up the spine from below and plug the spine's tabs into the base. Fit the end plates over the tabs of the base, the rings and the spine, then screw them on: a nut dro

Layered Shadow Box
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Layered Shadow Box

Shadow box: a layered landscape in a frame. Each layer is a range of hills joined to its own border, the nearest with a row of pine trees, in front of a night sky engraved with a moon and stars. Spacer frames between the layers give the scene its depth and shadows. Change the seed for a different landscape. Assembly: glue the stack together from the back, layer, spacer, layer, lining up the outer edges. Hang it from the keyhole in the back, or stand it on a shelf. A strip of LEDs behind the front frame lights it.