Retour: Communauté
MyLaserTools.com

Iris Box

Iris box: a round box whose lid opens like a camera shutter. Eight curved blades meet in the middle; turn the ring on top and pins under it swing every blade…

par Kerf Designs

Réglages

Unités

Box

Diameter
Outside diameter
Height
Height of the box under the lid
Staves
Wall staves around the box

Assembled view

Open
How far the iris is open, 0 to 1

Material

Épaisseur du matériau
La plaque que vous découpez. Les fentes et les tenons s'y adaptent.
mm
Largeur de coupe
Largeur de matériau brûlée par le laser.
mm
Pin
Pin diameter for the pivots and the drive
Clearance

Aperçu 3D

Génération de votre modèle
Palette d'inspiration

Code

Copier dans l'atelier

Photos

Iris Box

À propos de cette création

Découpe laser et Impression 3D

Iris box: a round box whose lid opens like a camera shutter. Eight curved blades meet in the middle; turn the ring on top and pins under it swing every blade out on its own pivot, opening a round hole to reach in. The blades lie flat side by side and never overlap, so they can be cut from a flat sheet: walnut here, against the plywood box. Assembly: plug the staves into the base and the deck and glue them. Glue a pivot pin into each hole in the deck, drop the blades on, and glue the guard ring round them. Glue a drive pin into each hole in the drive ring, set it on with the pins in the blade s

BoîtesCadeauxMaquettes
boxesmechanismsgifts

Usage personnelUsage commercial

Qu'est-ce que cela signifie ?

Comment la fabriquer

  1. 1Modifiez les réglages. L'aperçu se met à jour après chaque modification.
  2. 2Téléchargez le SVG pour votre laser, ou ouvrez-le dans l'éditeur de créations pour le compléter.
  3. 3Aimez la création et ajoutez ci-dessous une photo de votre réalisation.

Questions

Oui. Vous pouvez la télécharger et l'utiliser gratuitement selon sa licence.

Oui. Modifiez les réglages sur cette page : l'aperçu se met à jour au fur et à mesure. Quand le résultat vous convient, téléchargez le fichier.

Un SVG pour votre logiciel laser. Vous pouvez aussi l'ouvrir dans l'éditeur de créations, ou télécharger des fichiers STL et 3MF à l'épaisseur du matériau pour imprimer les pièces.

La taille suit les réglages de cette page, et l'encadré de taille sous l'aperçu affiche le résultat.

Réglez l'épaisseur du matériau sur celle de la plaque que vous découpez. Les fentes et les tenons s'y adaptent.

Oui. La licence couvre l'usage personnel et commercial des objets que vous fabriquez.

Réalisé par la communauté

Vous avez découpé cette création ? Partagez une photo et une note sur votre expérience pour recevoir immédiatement 10 étincelles.

Je l'ai réalisé

Plus de créations de Kerf Designs

Locker Stall
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Locker Stall

A miniature for book nooks and dioramas. Locker stall: a miniature team locker with the player's jersey, for dioramas, shelves and a gift to any player. Two sides hold the back, a kick panel, a bench seat, a helmet shelf and a name board, all tabbed in; the jersey (team colours, name, number) hangs by a hole in its hanger on a peg tabbed into the back. Skates or cleats can stand on the seat, the helmet on the shelf. Hockey, soccer, basketball or baseball. Assembly: push the back, the kick panel, the seat, the shelf and the name board into one side, add the other, push the peg into the back, ha

Vampire Coffin
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Vampire Coffin

A miniature for book nooks and dioramas. Coffin: a miniature vampire's coffin for dioramas, Halloween and book nooks. A true coffin shape from every side: a stack of coffin-shaped rings on a solid floor, aligned by two keys that stand in the floor's slots and slide through notches in every ring; no corner joints to show. The lid is two layers, closed or slid half open on the velvet and the rose inside. It can stand on a stone plinth. Assembly: stand the keys in the floor, thread the rings down over them, glue each, lay the lid on; set it all on the plinth.

Library Bookcase
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Library Bookcase

A miniature for book nooks and dioramas. Library bookcase: a miniature bookcase with its rolling-style ladder, for dioramas, dollhouses and book nooks. The bookcase is a tab-and-slot box of sides, a back, shelves and a top, with rows of books standing in slots on every shelf and, with the ladder, a brass rail tabbed across the front. The ladder's two rails lean back to that rail and hook over it through notches in their tops; its treads tab into the rails and its feet stand in the base. One book on the top shelf has a ribbon bookmark with an initial on it. Assembly: build the bookcase and stan

Bread Rack
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Bread Rack

A miniature for book nooks and dioramas. Bread rack: a miniature bakery rack for dioramas, shop fronts and book nooks. Two ladder ends (legs, a band at every shelf, cut-outs between) hold slatted shelves tabbed into them, and the bread stands in slots on the shelves: round loaves, croissants, and baguettes in a basket on top. Assembly: push the shelves into one ladder end, add the other, stand the bread in its slots, set the feet in the base.

Créations similaires

Café Table Caddy
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Café Table Caddy

Table caddy: a café table organiser. Two low bins at the front for sugar and sachets, a napkin compartment behind them with a scoop to reach in, and a tall back panel with a pocket behind it for a table number or a small menu card, facing the other side of the table. The café's name is engraved along the front. Every panel tabs into the two stepped sides, and the divider between the bins into the bottom. Assembly: push the bottom's and the panels' tabs into one side, then press the other side on. Drop the divider into its slots. A drop of glue in each slot makes it permanent; finish with a foo

Slat Crate
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Slat Crate

Slat crate: two solid end panels with carry handles, joined by spaced slats on the front, back and floor. Each slat ends in a tab that goes through a slot in the end panels, so the crate needs no corner posts. Use 6 mm plywood or thicker for a crate that carries a load. Assembly: push the slat tabs through both ends, square it and glue.

Roll-Top Shutter Box
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Roll-Top Shutter Box

Shutter box: a box with a roll-top lid. The lid is a row of slats whose narrow ends ride in a channel inside each side, so it slides back round the curved corner and down behind the back wall. The channel is the gap left between a guide plate and a rim, glued to each side wall. Assembly: glue a guide and a rim to each side wall, fit the front, back and bottom into one side and add the other. Glue the slats face down on a strip of canvas, leaving their ends free, and slide them in from the front.

Pivot Lid Box
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Pivot Lid Box

Pivot box: a finger-jointed box whose lid swings open on two dowels. Cheeks under the lid hang outside the side walls and turn on the dowels. The walls' back corners are rounded about the dowels and the back wall stops at their height, so the lid can turn up to upright without catching anything. Assembly: glue the box. Glue the cheeks into the lid, then push a dowel through each cheek into its side wall, a snug fit in the wall and free in the cheek.