Retour: Communauté
MyLaserTools.com

Laminated screw press

Screw press: laminated platens and hand knobs with captive hex nuts. Clamp the lower platen onto four threaded rods using washers and nuts. Glue the knob…

par Kerf Designs

Réglages

Unités

Platens

Width
Depth
Platen layers
Margin
Rod height
Opening

Measured hardware

Rod diameter
Thread pitch
Nut flats
Nut height
Nut clearance
Washer height

Material

Épaisseur du matériau
La plaque que vous découpez. Les fentes et les tenons s'y adaptent.
mm
Largeur de coupe
Largeur de matériau brûlée par le laser.
mm

Aperçu 3D

Génération de votre modèle
Palette d'inspiration

Code

Copier dans l'atelier

Photos

Laminated screw press

À propos de cette création

Découpe laser et Impression 3D

Screw press: laminated platens and hand knobs with captive hex nuts. Clamp the lower platen onto four threaded rods using washers and nuts. Glue the knob laminations around measured hex nuts without gluing the threads. Put washers beneath the knobs and turn them evenly to press. A small craft press for paper and light glue-ups, not for heavy pressing.

MaquettesOutils
toolsworkshopmechanisms

Usage personnelUsage commercial

Qu'est-ce que cela signifie ?

Comment la fabriquer

  1. 1Modifiez les réglages. L'aperçu se met à jour après chaque modification.
  2. 2Téléchargez le SVG pour votre laser, ou ouvrez-le dans l'éditeur de créations pour le compléter.
  3. 3Aimez la création et ajoutez ci-dessous une photo de votre réalisation.

Questions

Oui. Vous pouvez la télécharger et l'utiliser gratuitement selon sa licence.

Oui. Modifiez les réglages sur cette page : l'aperçu se met à jour au fur et à mesure. Quand le résultat vous convient, téléchargez le fichier.

Un SVG pour votre logiciel laser. Vous pouvez aussi l'ouvrir dans l'éditeur de créations, ou télécharger des fichiers STL et 3MF à l'épaisseur du matériau pour imprimer les pièces.

La taille suit les réglages de cette page, et l'encadré de taille sous l'aperçu affiche le résultat.

Réglez l'épaisseur du matériau sur celle de la plaque que vous découpez. Les fentes et les tenons s'y adaptent.

Oui. La licence couvre l'usage personnel et commercial des objets que vous fabriquez.

Réalisé par la communauté

Vous avez découpé cette création ? Partagez une photo et une note sur votre expérience pour recevoir immédiatement 10 étincelles.

Je l'ai réalisé

Plus de créations de Kerf Designs

Locker Stall
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Locker Stall

A miniature for book nooks and dioramas. Locker stall: a miniature team locker with the player's jersey, for dioramas, shelves and a gift to any player. Two sides hold the back, a kick panel, a bench seat, a helmet shelf and a name board, all tabbed in; the jersey (team colours, name, number) hangs by a hole in its hanger on a peg tabbed into the back. Skates or cleats can stand on the seat, the helmet on the shelf. Hockey, soccer, basketball or baseball. Assembly: push the back, the kick panel, the seat, the shelf and the name board into one side, add the other, push the peg into the back, ha

Vampire Coffin
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Vampire Coffin

A miniature for book nooks and dioramas. Coffin: a miniature vampire's coffin for dioramas, Halloween and book nooks. A true coffin shape from every side: a stack of coffin-shaped rings on a solid floor, aligned by two keys that stand in the floor's slots and slide through notches in every ring; no corner joints to show. The lid is two layers, closed or slid half open on the velvet and the rose inside. It can stand on a stone plinth. Assembly: stand the keys in the floor, thread the rings down over them, glue each, lay the lid on; set it all on the plinth.

Library Bookcase
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Library Bookcase

A miniature for book nooks and dioramas. Library bookcase: a miniature bookcase with its rolling-style ladder, for dioramas, dollhouses and book nooks. The bookcase is a tab-and-slot box of sides, a back, shelves and a top, with rows of books standing in slots on every shelf and, with the ladder, a brass rail tabbed across the front. The ladder's two rails lean back to that rail and hook over it through notches in their tops; its treads tab into the rails and its feet stand in the base. One book on the top shelf has a ribbon bookmark with an initial on it. Assembly: build the bookcase and stan

Bread Rack
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Bread Rack

A miniature for book nooks and dioramas. Bread rack: a miniature bakery rack for dioramas, shop fronts and book nooks. Two ladder ends (legs, a band at every shelf, cut-outs between) hold slatted shelves tabbed into them, and the bread stands in slots on the shelves: round loaves, croissants, and baguettes in a basket on top. Assembly: push the shelves into one ladder end, add the other, stand the bread in its slots, set the feet in the base.

Créations similaires

Vernier Caliper
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Vernier Caliper

Vernier caliper: a working sliding caliper that reads to a tenth of a millimetre and to 1/128 inch. The main scales are scored along the beam and seen through a window in the slider, whose vernier scales sit right against them. Outside jaws below, inside jaws above. How to read it: the slider's 0 gives whole millimetres on the beam; the vernier line that meets a beam line exactly gives the tenths. Assembly: slide the slider plates over the beam with the spacers above and below it, then rivet or pin them through the holes. Cut it from acrylic or a stable plywood for the best accuracy.

Ball Caster
PersonnalisablesGratuit
Impression 3D
par Hardware Designs

Ball Caster

A snap-in caster for steel balls, marbles and airsoft BBs from 5 to 40 mm, for robots, carts, drawers and sliding furniture. Two ears, three ears, a round flange or no flange, with an optional riser. Prints flange down with no supports. Press the ball in until the fingers click over it.

Roll-Top Shutter Box
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Roll-Top Shutter Box

Shutter box: a box with a roll-top lid. The lid is a row of slats whose narrow ends ride in a channel inside each side, so it slides back round the curved corner and down behind the back wall. The channel is the gap left between a guide plate and a rim, glued to each side wall. Assembly: glue a guide and a rim to each side wall, fit the front, back and bottom into one side and add the other. Glue the slats face down on a strip of canvas, leaving their ends free, and slide them in from the front.

Pulley Wheel
PersonnalisablesGratuit
Impression 3D
par Hardware Designs

Pulley Wheel

A grooved sheave for rope, cord and wire, with a seat for a 608, 625 or 623 skate bearing or a plain bore for a bolt. For clothesline pulleys, plant hoists, bike ceiling lifts and kinetic builds. The 45 degree V groove keeps the rope centred. Prints flat with no supports.