Indietro: Community
MyLaserTools.com

Corner Brackets and Mending Plates

Flat L and T plates, straight mending plates, 90 degree angle brackets with a gusset, and three-way inside corners for boxes, frames, shelves and printer…

di Hardware Designs

Impostazioni

Unità

Bracket

Type
Bracket type
Arm
Length of each arm in mm
mm
Width
Width of each arm in mm
mm
Thickness
Plate thickness in mm
mm
Gusset
Add a stiffening gusset to angle and corner brackets

Holes

Holes
Screw holes per arm
Screw
Screw hole diameter in mm
mm

Print

Count
Number of brackets

Anteprima 3D

Generazione del modello
Palette di ispirazione

Codice

Copia nel Banco di lavoro

Foto

Corner Brackets and Mending Plates

Informazioni su questo design

Scritto in OpenSCAD · Stampa 3D

Flat L and T plates, straight mending plates, 90 degree angle brackets with a gusset, and three-way inside corners for boxes, frames, shelves and printer enclosures. Set the arm length, width, thickness and screw holes per arm.

Holes in upright faces have pointed tops, so every type prints with no supports.

Esclusivo per Stampa 3DFerramentaStrumenti
bracketcorner bracemending plateshelf

Uso personaleUso commerciale

Che cosa significa?

Come realizzarlo

  1. 1Cambia le impostazioni. L'anteprima si aggiorna a ogni modifica.
  2. 2Scarica lo STL per qualsiasi slicer, oppure il 3MF per tenere separati i pezzi colorati.
  3. 3Metti Mi piace al design e aggiungi qui sotto una foto di quello che hai realizzato.

Domande

Sì. È gratuito da scaricare e da usare secondo la sua licenza.

Sì. Cambia le impostazioni in questa pagina e l'anteprima si aggiorna mentre lavori. Quando ti convince, scarica il file.

Uno STL per qualsiasi slicer e un 3MF che mantiene ogni pezzo colorato come oggetto a sé.

La dimensione segue le impostazioni di questa pagina, e il riquadro delle misure sotto l'anteprima mostra il risultato.

Sì. La licenza copre l'uso personale e commerciale dei pezzi che realizzi.

Realizzato dalla community

Lo hai tagliato? Condividi una foto e una nota su come è andata e ricevi subito 10 scintille.

L'ho realizzato

Altri di Hardware Designs

Crank Handle
PersonalizzabileGratis
Stampa 3D
di Hardware Designs

Crank Handle

A hand crank with a square, hex, round or D bore and a grip that spins on its pin. For awning winders, pasta rollers, window cranks, winches and anything with an adjusting screw. The arm prints flat and the grip prints upright, then snaps onto the pin. A pointed set screw hole holds it on the shaft.

Flanged and Cap Nuts
PersonalizzabileGratis
Stampa 3D
di Hardware Designs

Flanged and Cap Nuts

Printed hex nuts with a washer flange that spreads the load on wood and plastic, or a domed cap that covers the sharp end of the bolt. Metric and UNC sizes, with a clearance setting so the thread suits your printer. Prints upright with no supports, several at once.

Lever Handle Nut
PersonalizzabileGratis
Stampa 3D
di Hardware Designs

Lever Handle Nut

A clamping lever for router fences, drill press tables, tool rests and camera rigs, where a round knob slips in your hand. Straight, cranked or paddle lever, 35 to 140 mm long. Use a printed thread, a pocket for a steel nut, or a bolt head pocket. Prints flat with no supports.

Wing and Thumb Nuts
PersonalizzabileGratis
Stampa 3D
di Hardware Designs

Wing and Thumb Nuts

Hand-tightened nuts for M5 to M12 and 1/4 to 1/2 inch bolts, in wing, big wing, knurled, star and lobed shapes. Pick a printed thread, a pocket that grips a steel nut, or a pocket for a bolt head to turn it into a thumb screw. Prints upright with no supports. Printed threads hold best from M6 and 1/4 inch up; below that use the steel nut pocket.

Design simili

Turnbuckle
PersonalizzabileGratis
Stampa 3D
di Hardware Designs

Turnbuckle

A fully printed turnbuckle with one right-hand and one left-hand eye bolt. Turning the body draws both eyes in, for tightening garden wire, shade sails, banner lines and display rigging. The left-hand eye has a notch and the left-hand end of the body has a groove, so you can tell them apart. All three parts print upright with no supports.

Strap Slides and Line Tensioners
PersonalizzabileGratis
Stampa 3D
di Hardware Designs

Strap Slides and Line Tensioners

Tri-glide adjusters, strap keepers and D-rings for 10 to 50 mm webbing, plus three-hole tensioners for tent guy lines and clotheslines. Everything prints flat with no supports, a sheet at a time.

Rope Cleat
PersonalizzabileGratis
Stampa 3D
di Hardware Designs

Rope Cleat

A horn cleat for tying off flag lines, blind cords, tarps, hammocks and garden netting with a quick figure-eight. Set the length, rope size and width, and bolt it down through both posts. Prints upright with no supports. The horns rise at 45 degrees.

Tie-Down Ring
PersonalizzabileGratis
Stampa 3D
di Hardware Designs

Tie-Down Ring

A folding D-ring anchor for truck beds, trailers, crates, garden netting and gym straps. The ring comes off the bed already trapped under its strap, and folds flat when you are not using it. Prints flat in place with no supports. Screw down both pads.