Indietro: Community
MyLaserTools.com

Rope Cleat

A horn cleat for tying off flag lines, blind cords, tarps, hammocks and garden netting with a quick figure-eight. Set the length, rope size and width, and…

di Hardware Designs

Impostazioni

Unità

Cleat

Length
Overall length in mm
mm
Rope
Rope diameter in mm
mm
Width
Width in mm
mm

Mounting

Screw
Bolt or screw hole diameter in mm
mm

Print

Count
Number of cleats

Anteprima 3D

Generazione del modello
Palette di ispirazione

Codice

Copia nel Banco di lavoro

Foto

Rope Cleat

Informazioni su questo design

Scritto in OpenSCAD · Stampa 3D

A horn cleat for tying off flag lines, blind cords, tarps, hammocks and garden netting with a quick figure-eight. Set the length, rope size and width, and bolt it down through both posts.

Prints upright with no supports. The horns rise at 45 degrees.

Esclusivo per Stampa 3DFerramenta
cleatropeboatflag pole

Uso personaleUso commerciale

Che cosa significa?

Come realizzarlo

  1. 1Cambia le impostazioni. L'anteprima si aggiorna a ogni modifica.
  2. 2Scarica lo STL per qualsiasi slicer, oppure il 3MF per tenere separati i pezzi colorati.
  3. 3Metti Mi piace al design e aggiungi qui sotto una foto di quello che hai realizzato.

Domande

Sì. È gratuito da scaricare e da usare secondo la sua licenza.

Sì. Cambia le impostazioni in questa pagina e l'anteprima si aggiorna mentre lavori. Quando ti convince, scarica il file.

Uno STL per qualsiasi slicer e un 3MF che mantiene ogni pezzo colorato come oggetto a sé.

La dimensione segue le impostazioni di questa pagina, e il riquadro delle misure sotto l'anteprima mostra il risultato.

Sì. La licenza copre l'uso personale e commerciale dei pezzi che realizzi.

Realizzato dalla community

Lo hai tagliato? Condividi una foto e una nota su come è andata e ricevi subito 10 scintille.

L'ho realizzato

Altri di Hardware Designs

Crank Handle
PersonalizzabileGratis
Stampa 3D
di Hardware Designs

Crank Handle

A hand crank with a square, hex, round or D bore and a grip that spins on its pin. For awning winders, pasta rollers, window cranks, winches and anything with an adjusting screw. The arm prints flat and the grip prints upright, then snaps onto the pin. A pointed set screw hole holds it on the shaft.

Flanged and Cap Nuts
PersonalizzabileGratis
Stampa 3D
di Hardware Designs

Flanged and Cap Nuts

Printed hex nuts with a washer flange that spreads the load on wood and plastic, or a domed cap that covers the sharp end of the bolt. Metric and UNC sizes, with a clearance setting so the thread suits your printer. Prints upright with no supports, several at once.

Lever Handle Nut
PersonalizzabileGratis
Stampa 3D
di Hardware Designs

Lever Handle Nut

A clamping lever for router fences, drill press tables, tool rests and camera rigs, where a round knob slips in your hand. Straight, cranked or paddle lever, 35 to 140 mm long. Use a printed thread, a pocket for a steel nut, or a bolt head pocket. Prints flat with no supports.

Wing and Thumb Nuts
PersonalizzabileGratis
Stampa 3D
di Hardware Designs

Wing and Thumb Nuts

Hand-tightened nuts for M5 to M12 and 1/4 to 1/2 inch bolts, in wing, big wing, knurled, star and lobed shapes. Pick a printed thread, a pocket that grips a steel nut, or a pocket for a bolt head to turn it into a thumb screw. Prints upright with no supports. Printed threads hold best from M6 and 1/4 inch up; below that use the steel nut pocket.

Design simili

Turnbuckle
PersonalizzabileGratis
Stampa 3D
di Hardware Designs

Turnbuckle

A fully printed turnbuckle with one right-hand and one left-hand eye bolt. Turning the body draws both eyes in, for tightening garden wire, shade sails, banner lines and display rigging. The left-hand eye has a notch and the left-hand end of the body has a groove, so you can tell them apart. All three parts print upright with no supports.

Strap Slides and Line Tensioners
PersonalizzabileGratis
Stampa 3D
di Hardware Designs

Strap Slides and Line Tensioners

Tri-glide adjusters, strap keepers and D-rings for 10 to 50 mm webbing, plus three-hole tensioners for tent guy lines and clotheslines. Everything prints flat with no supports, a sheet at a time.

Tie-Down Ring
PersonalizzabileGratis
Stampa 3D
di Hardware Designs

Tie-Down Ring

A folding D-ring anchor for truck beds, trailers, crates, garden netting and gym straps. The ring comes off the bed already trapped under its strap, and folds flat when you are not using it. Prints flat in place with no supports. Screw down both pads.

Table Corner Guards
PersonalizzabileGratis
Stampa 3D
di Hardware Designs

Table Corner Guards

Rounded covers for sharp table, desk, shelf and hearth corners, sized to the thickness of the top. Use double-sided tape, or turn on the lip that hooks under the edge. Prints upside down with no supports. TPU gives a softer bump.