Retour: Communauté
MyLaserTools.com

Thread Spool Rack

Spool rack: a desk stand for sewing thread, with a peg for every spool and room on each peg for its matching bobbin underneath. The board leans back so the…

par Kerf Designs

Réglages

Unités

Rack

Columns
Pegs across
Rows
Rows of pegs
Spool
Spool diameter
Spool height
Spool and bobbin height together
Lean
Lean of the board back from upright

Material

Épaisseur du matériau
La plaque que vous découpez. Les fentes et les tenons s'y adaptent.
mm
Largeur de coupe
Largeur de matériau brûlée par le laser.
mm
Clearance
Peg
Peg diameter

Aperçu 3D

Génération de votre modèle
Palette d'inspiration

Code

Copier dans l'atelier

Photos

Thread Spool Rack

À propos de cette création

Découpe laser et Impression 3D

Spool rack: a desk stand for sewing thread, with a peg for every spool and room on each peg for its matching bobbin underneath. The board leans back so the spools stay on, its tabs slot into the two sides, and a shelf along the front holds scissors and pins. Size it for your spools and the number of colours you keep. Assembly: glue a 6 mm dowel peg into each hole, slot the board and the shelf into one side, then press the other side on, and glue the joints so the rack stays square under the weight of the spools.

Outils
tools

Usage personnelUsage commercial

Qu'est-ce que cela signifie ?

Comment la fabriquer

  1. 1Modifiez les réglages. L'aperçu se met à jour après chaque modification.
  2. 2Téléchargez le SVG pour votre laser, ou ouvrez-le dans l'éditeur de créations pour le compléter.
  3. 3Aimez la création et ajoutez ci-dessous une photo de votre réalisation.

Questions

Oui. Vous pouvez la télécharger et l'utiliser gratuitement selon sa licence.

Oui. Modifiez les réglages sur cette page : l'aperçu se met à jour au fur et à mesure. Quand le résultat vous convient, téléchargez le fichier.

Un SVG pour votre logiciel laser. Vous pouvez aussi l'ouvrir dans l'éditeur de créations, ou télécharger des fichiers STL et 3MF à l'épaisseur du matériau pour imprimer les pièces.

La taille suit les réglages de cette page, et l'encadré de taille sous l'aperçu affiche le résultat.

Réglez l'épaisseur du matériau sur celle de la plaque que vous découpez. Les fentes et les tenons s'y adaptent.

Oui. La licence couvre l'usage personnel et commercial des objets que vous fabriquez.

Réalisé par la communauté

Vous avez découpé cette création ? Partagez une photo et une note sur votre expérience pour recevoir immédiatement 10 étincelles.

Je l'ai réalisé

Plus de créations de Kerf Designs

Locker Stall
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Locker Stall

A miniature for book nooks and dioramas. Locker stall: a miniature team locker with the player's jersey, for dioramas, shelves and a gift to any player. Two sides hold the back, a kick panel, a bench seat, a helmet shelf and a name board, all tabbed in; the jersey (team colours, name, number) hangs by a hole in its hanger on a peg tabbed into the back. Skates or cleats can stand on the seat, the helmet on the shelf. Hockey, soccer, basketball or baseball. Assembly: push the back, the kick panel, the seat, the shelf and the name board into one side, add the other, push the peg into the back, ha

Vampire Coffin
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Vampire Coffin

A miniature for book nooks and dioramas. Coffin: a miniature vampire's coffin for dioramas, Halloween and book nooks. A true coffin shape from every side: a stack of coffin-shaped rings on a solid floor, aligned by two keys that stand in the floor's slots and slide through notches in every ring; no corner joints to show. The lid is two layers, closed or slid half open on the velvet and the rose inside. It can stand on a stone plinth. Assembly: stand the keys in the floor, thread the rings down over them, glue each, lay the lid on; set it all on the plinth.

Library Bookcase
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Library Bookcase

A miniature for book nooks and dioramas. Library bookcase: a miniature bookcase with its rolling-style ladder, for dioramas, dollhouses and book nooks. The bookcase is a tab-and-slot box of sides, a back, shelves and a top, with rows of books standing in slots on every shelf and, with the ladder, a brass rail tabbed across the front. The ladder's two rails lean back to that rail and hook over it through notches in their tops; its treads tab into the rails and its feet stand in the base. One book on the top shelf has a ribbon bookmark with an initial on it. Assembly: build the bookcase and stan

Bread Rack
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Bread Rack

A miniature for book nooks and dioramas. Bread rack: a miniature bakery rack for dioramas, shop fronts and book nooks. Two ladder ends (legs, a band at every shelf, cut-outs between) hold slatted shelves tabbed into them, and the bread stands in slots on the shelves: round loaves, croissants, and baguettes in a basket on top. Assembly: push the shelves into one ladder end, add the other, stand the bread in its slots, set the feet in the base.

Créations similaires

Yarn Bobbins
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Yarn Bobbins

Yarn bobbins: a set of flat bobbins for leftover yarn, embroidery floss or ribbon. The yarn winds round the waist between the notches, a slit in the top holds the loose end, and each bobbin is numbered so you can write down the colour. The hole takes a ring to keep a set together. Finishing: sand the edges so they don't catch the yarn.

Turnbuckle
PersonnalisablesGratuit
Impression 3D
par Hardware Designs

Turnbuckle

A fully printed turnbuckle with one right-hand and one left-hand eye bolt. Turning the body draws both eyes in, for tightening garden wire, shade sails, banner lines and display rigging. The left-hand eye has a notch and the left-hand end of the body has a groove, so you can tell them apart. All three parts print upright with no supports.

Vernier Caliper
PersonnalisablesGratuit
Découpe laserImpression 3D
par Kerf Designs

Vernier Caliper

Vernier caliper: a working sliding caliper that reads to a tenth of a millimetre and to 1/128 inch. The main scales are scored along the beam and seen through a window in the slider, whose vernier scales sit right against them. Outside jaws below, inside jaws above. How to read it: the slider's 0 gives whole millimetres on the beam; the vernier line that meets a beam line exactly gives the tenths. Assembly: slide the slider plates over the beam with the spacers above and below it, then rivet or pin them through the holes. Cut it from acrylic or a stable plywood for the best accuracy.

Wing and Thumb Nuts
PersonnalisablesGratuit
Impression 3D
par Hardware Designs

Wing and Thumb Nuts

Hand-tightened nuts for M5 to M12 and 1/4 to 1/2 inch bolts, in wing, big wing, knurled, star and lobed shapes. Pick a printed thread, a pocket that grips a steel nut, or a pocket for a bolt head to turn it into a thumb screw. Prints upright with no supports. Printed threads hold best from M6 and 1/4 inch up; below that use the steel nut pocket.