Retour: Communauté
MyLaserTools.com

Hidden Panel Connectors

Two-part dovetail connectors that join shelves, headboards, cabinet sides and wall panels with no screws showing. The tail tapers half a millimetre along its…

par Hardware Designs

Réglages

Unités

Connector

Length
Connector length in mm
mm
Width
Connector width in mm
mm
Clearance
Gap between the halves in mm
mm
Screw
Screw hole diameter in mm
mm

Jig

Inset
Distance from the panel edge to the connector centre in mm
mm

Print

Parts
Parts to print
Count
Number of connector pairs

Aperçu 3D

Génération de votre modèle
Palette d'inspiration

Code

Copier dans l'atelier

Photos

Hidden Panel Connectors

À propos de cette création

Écrit en OpenSCAD · Impression 3D

Two-part dovetail connectors that join shelves, headboards, cabinet sides and wall panels with no screws showing. The tail tapers half a millimetre along its length, so sliding the halves together pulls the joint tight.

A marking jig with a fence puts both halves at the same distance from the edge on each panel. All parts print flat.

Exclusivement pour l'impression 3DQuincaillerieOutils
connectorfurniturejoinerydovetail

Usage personnelUsage commercial

Qu'est-ce que cela signifie ?

Comment la fabriquer

  1. 1Modifiez les réglages. L'aperçu se met à jour après chaque modification.
  2. 2Téléchargez le STL pour tout logiciel de tranchage, ou le 3MF pour conserver les pièces colorées séparées.
  3. 3Aimez la création et ajoutez ci-dessous une photo de votre réalisation.

Questions

Oui. Vous pouvez la télécharger et l'utiliser gratuitement selon sa licence.

Oui. Modifiez les réglages sur cette page : l'aperçu se met à jour au fur et à mesure. Quand le résultat vous convient, téléchargez le fichier.

Un STL pour tout logiciel de tranchage, et un 3MF où chaque pièce colorée reste un objet distinct.

La taille suit les réglages de cette page, et l'encadré de taille sous l'aperçu affiche le résultat.

Oui. La licence couvre l'usage personnel et commercial des objets que vous fabriquez.

Réalisé par la communauté

Vous avez découpé cette création ? Partagez une photo et une note sur votre expérience pour recevoir immédiatement 10 étincelles.

Je l'ai réalisé

Plus de créations de Hardware Designs

Crank Handle
PersonnalisablesGratuit
Impression 3D
par Hardware Designs

Crank Handle

A hand crank with a square, hex, round or D bore and a grip that spins on its pin. For awning winders, pasta rollers, window cranks, winches and anything with an adjusting screw. The arm prints flat and the grip prints upright, then snaps onto the pin. A pointed set screw hole holds it on the shaft.

Flanged and Cap Nuts
PersonnalisablesGratuit
Impression 3D
par Hardware Designs

Flanged and Cap Nuts

Printed hex nuts with a washer flange that spreads the load on wood and plastic, or a domed cap that covers the sharp end of the bolt. Metric and UNC sizes, with a clearance setting so the thread suits your printer. Prints upright with no supports, several at once.

Lever Handle Nut
PersonnalisablesGratuit
Impression 3D
par Hardware Designs

Lever Handle Nut

A clamping lever for router fences, drill press tables, tool rests and camera rigs, where a round knob slips in your hand. Straight, cranked or paddle lever, 35 to 140 mm long. Use a printed thread, a pocket for a steel nut, or a bolt head pocket. Prints flat with no supports.

Wing and Thumb Nuts
PersonnalisablesGratuit
Impression 3D
par Hardware Designs

Wing and Thumb Nuts

Hand-tightened nuts for M5 to M12 and 1/4 to 1/2 inch bolts, in wing, big wing, knurled, star and lobed shapes. Pick a printed thread, a pocket that grips a steel nut, or a pocket for a bolt head to turn it into a thumb screw. Prints upright with no supports. Printed threads hold best from M6 and 1/4 inch up; below that use the steel nut pocket.

Créations similaires

Turnbuckle
PersonnalisablesGratuit
Impression 3D
par Hardware Designs

Turnbuckle

A fully printed turnbuckle with one right-hand and one left-hand eye bolt. Turning the body draws both eyes in, for tightening garden wire, shade sails, banner lines and display rigging. The left-hand eye has a notch and the left-hand end of the body has a groove, so you can tell them apart. All three parts print upright with no supports.

Strap Slides and Line Tensioners
PersonnalisablesGratuit
Impression 3D
par Hardware Designs

Strap Slides and Line Tensioners

Tri-glide adjusters, strap keepers and D-rings for 10 to 50 mm webbing, plus three-hole tensioners for tent guy lines and clotheslines. Everything prints flat with no supports, a sheet at a time.

Rope Cleat
PersonnalisablesGratuit
Impression 3D
par Hardware Designs

Rope Cleat

A horn cleat for tying off flag lines, blind cords, tarps, hammocks and garden netting with a quick figure-eight. Set the length, rope size and width, and bolt it down through both posts. Prints upright with no supports. The horns rise at 45 degrees.

Tie-Down Ring
PersonnalisablesGratuit
Impression 3D
par Hardware Designs

Tie-Down Ring

A folding D-ring anchor for truck beds, trailers, crates, garden netting and gym straps. The ring comes off the bed already trapped under its strap, and folds flat when you are not using it. Prints flat in place with no supports. Screw down both pads.