Indietro: Community
MyLaserTools.com

A-Frame Sign

A-frame sign: a tabletop sandwich board for a counter, a market stall or a party. Each leaf is a plywood frame over a chalkboard panel with your words…

di Kerf Designs

Impostazioni

Unità

Sign

Height
Height of a leaf
Width
Width
Spread
Half the angle between the leaves
Title
Front heading
Lines
Lines under it, split with |
Back title
Back heading
Top
Top of the frames

Material

Spessore del materiale
Il foglio che tagli. Fessure e linguette si adeguano.
mm
Kerf
Quanto materiale il laser brucia via.
mm
Clearance
Board
Chalkboard panel thickness

Anteprima 3D

Generazione del modello
Palette di ispirazione

Codice

Copia nel Banco di lavoro

Foto

A-Frame Sign

Informazioni su questo design

Taglio laser e Stampa 3D

A-frame sign: a tabletop sandwich board for a counter, a market stall or a party. Each leaf is a plywood frame over a chalkboard panel with your words engraved on the board, so they never rub off, and room below to chalk the day's specials. Tabs on top of both leaves come up through a cap that sets the spread and makes the carrying handle, and a short peg through each tab above the cap locks them, so lifting by the handle carries the whole sign. Pull the pegs and it packs flat. Assembly: glue each chalkboard panel behind its frame. Stand the leaves up, press the cap down over their tabs and pu

Esposizioni per negoziTesto
displayssigns

Uso personaleUso commerciale

Che cosa significa?

Come realizzarlo

  1. 1Cambia le impostazioni. L'anteprima si aggiorna a ogni modifica.
  2. 2Scarica l'SVG per il tuo laser, oppure aprilo nell'Editor di design per aggiungerci altro.
  3. 3Metti Mi piace al design e aggiungi qui sotto una foto di quello che hai realizzato.

Domande

Sì. È gratuito da scaricare e da usare secondo la sua licenza.

Sì. Cambia le impostazioni in questa pagina e l'anteprima si aggiorna mentre lavori. Quando ti convince, scarica il file.

Un SVG per il software del tuo laser. Puoi anche aprirlo nell'Editor di design, oppure scaricare STL e 3MF allo spessore del materiale per stampare i pezzi.

La dimensione segue le impostazioni di questa pagina, e il riquadro delle misure sotto l'anteprima mostra il risultato.

Imposta lo spessore del materiale uguale a quello del foglio che tagli. Linguette e fessure si adeguano.

Sì. La licenza copre l'uso personale e commerciale dei pezzi che realizzi.

Realizzato dalla community

Lo hai tagliato? Condividi una foto e una nota su come è andata e ricevi subito 10 scintille.

L'ho realizzato

Altri di Kerf Designs

Locker Stall
PersonalizzabileGratis
Taglio laserStampa 3D
di Kerf Designs

Locker Stall

A miniature for book nooks and dioramas. Locker stall: a miniature team locker with the player's jersey, for dioramas, shelves and a gift to any player. Two sides hold the back, a kick panel, a bench seat, a helmet shelf and a name board, all tabbed in; the jersey (team colours, name, number) hangs by a hole in its hanger on a peg tabbed into the back. Skates or cleats can stand on the seat, the helmet on the shelf. Hockey, soccer, basketball or baseball. Assembly: push the back, the kick panel, the seat, the shelf and the name board into one side, add the other, push the peg into the back, ha

Vampire Coffin
PersonalizzabileGratis
Taglio laserStampa 3D
di Kerf Designs

Vampire Coffin

A miniature for book nooks and dioramas. Coffin: a miniature vampire's coffin for dioramas, Halloween and book nooks. A true coffin shape from every side: a stack of coffin-shaped rings on a solid floor, aligned by two keys that stand in the floor's slots and slide through notches in every ring; no corner joints to show. The lid is two layers, closed or slid half open on the velvet and the rose inside. It can stand on a stone plinth. Assembly: stand the keys in the floor, thread the rings down over them, glue each, lay the lid on; set it all on the plinth.

Library Bookcase
PersonalizzabileGratis
Taglio laserStampa 3D
di Kerf Designs

Library Bookcase

A miniature for book nooks and dioramas. Library bookcase: a miniature bookcase with its rolling-style ladder, for dioramas, dollhouses and book nooks. The bookcase is a tab-and-slot box of sides, a back, shelves and a top, with rows of books standing in slots on every shelf and, with the ladder, a brass rail tabbed across the front. The ladder's two rails lean back to that rail and hook over it through notches in their tops; its treads tab into the rails and its feet stand in the base. One book on the top shelf has a ribbon bookmark with an initial on it. Assembly: build the bookcase and stan

Bread Rack
PersonalizzabileGratis
Taglio laserStampa 3D
di Kerf Designs

Bread Rack

A miniature for book nooks and dioramas. Bread rack: a miniature bakery rack for dioramas, shop fronts and book nooks. Two ladder ends (legs, a band at every shelf, cut-outs between) hold slatted shelves tabbed into them, and the bread stands in slots on the shelves: round loaves, croissants, and baguettes in a basket on top. Assembly: push the shelves into one ladder end, add the other, stand the bread in its slots, set the feet in the base.

Design simili

Café Table Caddy
PersonalizzabileGratis
Taglio laserStampa 3D
di Kerf Designs

Café Table Caddy

Table caddy: a café table organiser. Two low bins at the front for sugar and sachets, a napkin compartment behind them with a scoop to reach in, and a tall back panel with a pocket behind it for a table number or a small menu card, facing the other side of the table. The café's name is engraved along the front. Every panel tabs into the two stepped sides, and the divider between the bins into the bottom. Assembly: push the bottom's and the panels' tabs into one side, then press the other side on. Drop the divider into its slots. A drop of glue in each slot makes it permanent; finish with a foo

Sign Standoffs
PersonalizzabileGratis
Stampa 3D
di Hardware Designs

Sign Standoffs

Wall standoffs for acrylic, wood and metal signs. The barrel screws to the wall, and a threaded cap passes through the hole in the sign and clamps it, hiding the wall screw. Set the barrel size, the gap behind the sign and the sign thickness. The barrel prints upright and the cap prints face down, both with no supports.

Step Display
PersonalizzabileGratis
Taglio laserStampa 3D
di Kerf Designs

Step Display

Step display: a riser stand of tiers that climb to the back, for shop counters, nail polish, figures or cards. Every tread, riser and the back are tabbed through two stepped sides, so it squares itself as it goes together. A lip along each tread's front keeps round things from rolling off, and the sides are opened out to keep them light. Assembly: push the tabs of the treads, risers and back into one side, add the other side and glue. Glue each lip into its tread.

Slot Stand
PersonalizzabileGratis
Taglio laserStampa 3D
di Kerf Designs

Slot Stand

Slot stand: a display stand of just two pieces for a plate, a book, a tablet or a framed photo. The leaning back and the leg cross in a half-lap that follows the lean, so they slide together at the right angle without glue, and the leg's front end turns up into the ledge the item stands on. Set the item's size and the lean; the ledge is cut for the item's thickness. Assembly: slide the back down onto the leg along the lean.