Indietro: Community
MyLaserTools.com

Thread Spool Rack

Spool rack: a desk stand for sewing thread, with a peg for every spool and room on each peg for its matching bobbin underneath. The board leans back so the…

di Kerf Designs

Impostazioni

Unità

Rack

Columns
Pegs across
Rows
Rows of pegs
Spool
Spool diameter
Spool height
Spool and bobbin height together
Lean
Lean of the board back from upright

Material

Spessore del materiale
Il foglio che tagli. Fessure e linguette si adeguano.
mm
Kerf
Quanto materiale il laser brucia via.
mm
Clearance
Peg
Peg diameter

Anteprima 3D

Generazione del modello
Palette di ispirazione

Codice

Copia nel Banco di lavoro

Foto

Thread Spool Rack

Informazioni su questo design

Taglio laser e Stampa 3D

Spool rack: a desk stand for sewing thread, with a peg for every spool and room on each peg for its matching bobbin underneath. The board leans back so the spools stay on, its tabs slot into the two sides, and a shelf along the front holds scissors and pins. Size it for your spools and the number of colours you keep. Assembly: glue a 6 mm dowel peg into each hole, slot the board and the shelf into one side, then press the other side on, and glue the joints so the rack stays square under the weight of the spools.

Strumenti
tools

Uso personaleUso commerciale

Che cosa significa?

Come realizzarlo

  1. 1Cambia le impostazioni. L'anteprima si aggiorna a ogni modifica.
  2. 2Scarica l'SVG per il tuo laser, oppure aprilo nell'Editor di design per aggiungerci altro.
  3. 3Metti Mi piace al design e aggiungi qui sotto una foto di quello che hai realizzato.

Domande

Sì. È gratuito da scaricare e da usare secondo la sua licenza.

Sì. Cambia le impostazioni in questa pagina e l'anteprima si aggiorna mentre lavori. Quando ti convince, scarica il file.

Un SVG per il software del tuo laser. Puoi anche aprirlo nell'Editor di design, oppure scaricare STL e 3MF allo spessore del materiale per stampare i pezzi.

La dimensione segue le impostazioni di questa pagina, e il riquadro delle misure sotto l'anteprima mostra il risultato.

Imposta lo spessore del materiale uguale a quello del foglio che tagli. Linguette e fessure si adeguano.

Sì. La licenza copre l'uso personale e commerciale dei pezzi che realizzi.

Realizzato dalla community

Lo hai tagliato? Condividi una foto e una nota su come è andata e ricevi subito 10 scintille.

L'ho realizzato

Altri di Kerf Designs

Locker Stall
PersonalizzabileGratis
Taglio laserStampa 3D
di Kerf Designs

Locker Stall

A miniature for book nooks and dioramas. Locker stall: a miniature team locker with the player's jersey, for dioramas, shelves and a gift to any player. Two sides hold the back, a kick panel, a bench seat, a helmet shelf and a name board, all tabbed in; the jersey (team colours, name, number) hangs by a hole in its hanger on a peg tabbed into the back. Skates or cleats can stand on the seat, the helmet on the shelf. Hockey, soccer, basketball or baseball. Assembly: push the back, the kick panel, the seat, the shelf and the name board into one side, add the other, push the peg into the back, ha

Vampire Coffin
PersonalizzabileGratis
Taglio laserStampa 3D
di Kerf Designs

Vampire Coffin

A miniature for book nooks and dioramas. Coffin: a miniature vampire's coffin for dioramas, Halloween and book nooks. A true coffin shape from every side: a stack of coffin-shaped rings on a solid floor, aligned by two keys that stand in the floor's slots and slide through notches in every ring; no corner joints to show. The lid is two layers, closed or slid half open on the velvet and the rose inside. It can stand on a stone plinth. Assembly: stand the keys in the floor, thread the rings down over them, glue each, lay the lid on; set it all on the plinth.

Library Bookcase
PersonalizzabileGratis
Taglio laserStampa 3D
di Kerf Designs

Library Bookcase

A miniature for book nooks and dioramas. Library bookcase: a miniature bookcase with its rolling-style ladder, for dioramas, dollhouses and book nooks. The bookcase is a tab-and-slot box of sides, a back, shelves and a top, with rows of books standing in slots on every shelf and, with the ladder, a brass rail tabbed across the front. The ladder's two rails lean back to that rail and hook over it through notches in their tops; its treads tab into the rails and its feet stand in the base. One book on the top shelf has a ribbon bookmark with an initial on it. Assembly: build the bookcase and stan

Bread Rack
PersonalizzabileGratis
Taglio laserStampa 3D
di Kerf Designs

Bread Rack

A miniature for book nooks and dioramas. Bread rack: a miniature bakery rack for dioramas, shop fronts and book nooks. Two ladder ends (legs, a band at every shelf, cut-outs between) hold slatted shelves tabbed into them, and the bread stands in slots on the shelves: round loaves, croissants, and baguettes in a basket on top. Assembly: push the shelves into one ladder end, add the other, stand the bread in its slots, set the feet in the base.

Design simili

Yarn Bobbins
PersonalizzabileGratis
Taglio laserStampa 3D
di Kerf Designs

Yarn Bobbins

Yarn bobbins: a set of flat bobbins for leftover yarn, embroidery floss or ribbon. The yarn winds round the waist between the notches, a slit in the top holds the loose end, and each bobbin is numbered so you can write down the colour. The hole takes a ring to keep a set together. Finishing: sand the edges so they don't catch the yarn.

Turnbuckle
PersonalizzabileGratis
Stampa 3D
di Hardware Designs

Turnbuckle

A fully printed turnbuckle with one right-hand and one left-hand eye bolt. Turning the body draws both eyes in, for tightening garden wire, shade sails, banner lines and display rigging. The left-hand eye has a notch and the left-hand end of the body has a groove, so you can tell them apart. All three parts print upright with no supports.

Vernier Caliper
PersonalizzabileGratis
Taglio laserStampa 3D
di Kerf Designs

Vernier Caliper

Vernier caliper: a working sliding caliper that reads to a tenth of a millimetre and to 1/128 inch. The main scales are scored along the beam and seen through a window in the slider, whose vernier scales sit right against them. Outside jaws below, inside jaws above. How to read it: the slider's 0 gives whole millimetres on the beam; the vernier line that meets a beam line exactly gives the tenths. Assembly: slide the slider plates over the beam with the spacers above and below it, then rivet or pin them through the holes. Cut it from acrylic or a stable plywood for the best accuracy.

Wing and Thumb Nuts
PersonalizzabileGratis
Stampa 3D
di Hardware Designs

Wing and Thumb Nuts

Hand-tightened nuts for M5 to M12 and 1/4 to 1/2 inch bolts, in wing, big wing, knurled, star and lobed shapes. Pick a printed thread, a pocket that grips a steel nut, or a pocket for a bolt head to turn it into a thumb screw. Prints upright with no supports. Printed threads hold best from M6 and 1/4 inch up; below that use the steel nut pocket.