Indietro: Community
MyLaserTools.com

Horn Phone Stand

Horn phone stand: a solid block of layers that holds a phone at a lean and carries the sound of its speaker forward through a horn inside the block, flaring…

di Kerf Designs

Impostazioni

Unità

Phone

Phone width
Width of the phone, with its case
Phone thickness
Thickness of the phone, with its case
Lean
Lean back, from flat
Seat
How deep the phone sits

Material

Spessore del materiale
Il foglio che tagli. Fessure e linguette si adeguano.
mm
Kerf
Quanto materiale il laser brucia via.
mm
Clearance

Anteprima 3D

Generazione del modello
Palette di ispirazione

Codice

Copia nel Banco di lavoro

Foto

Horn Phone Stand

Informazioni su questo design

Taglio laser e Stampa 3D

Horn phone stand: a solid block of layers that holds a phone at a lean and carries the sound of its speaker forward through a horn inside the block, flaring out to the front. The slot leans because each layer's cut steps back a little from the one below; the horn is cut through the layers under the slot. The front steps down so the screen stays clear. Assembly: glue the layers in order, base first, lining up the backs.

Scrivania e ufficioFesta del papàRegali
officegiftsworkshop

Uso personaleUso commerciale

Che cosa significa?

Come realizzarlo

  1. 1Cambia le impostazioni. L'anteprima si aggiorna a ogni modifica.
  2. 2Scarica l'SVG per il tuo laser, oppure aprilo nell'Editor di design per aggiungerci altro.
  3. 3Metti Mi piace al design e aggiungi qui sotto una foto di quello che hai realizzato.

Domande

Sì. È gratuito da scaricare e da usare secondo la sua licenza.

Sì. Cambia le impostazioni in questa pagina e l'anteprima si aggiorna mentre lavori. Quando ti convince, scarica il file.

Un SVG per il software del tuo laser. Puoi anche aprirlo nell'Editor di design, oppure scaricare STL e 3MF allo spessore del materiale per stampare i pezzi.

La dimensione segue le impostazioni di questa pagina, e il riquadro delle misure sotto l'anteprima mostra il risultato.

Imposta lo spessore del materiale uguale a quello del foglio che tagli. Linguette e fessure si adeguano.

Sì. La licenza copre l'uso personale e commerciale dei pezzi che realizzi.

Realizzato dalla community

Lo hai tagliato? Condividi una foto e una nota su come è andata e ricevi subito 10 scintille.

L'ho realizzato

Altri di Kerf Designs

Locker Stall
PersonalizzabileGratis
Taglio laserStampa 3D
di Kerf Designs

Locker Stall

A miniature for book nooks and dioramas. Locker stall: a miniature team locker with the player's jersey, for dioramas, shelves and a gift to any player. Two sides hold the back, a kick panel, a bench seat, a helmet shelf and a name board, all tabbed in; the jersey (team colours, name, number) hangs by a hole in its hanger on a peg tabbed into the back. Skates or cleats can stand on the seat, the helmet on the shelf. Hockey, soccer, basketball or baseball. Assembly: push the back, the kick panel, the seat, the shelf and the name board into one side, add the other, push the peg into the back, ha

Vampire Coffin
PersonalizzabileGratis
Taglio laserStampa 3D
di Kerf Designs

Vampire Coffin

A miniature for book nooks and dioramas. Coffin: a miniature vampire's coffin for dioramas, Halloween and book nooks. A true coffin shape from every side: a stack of coffin-shaped rings on a solid floor, aligned by two keys that stand in the floor's slots and slide through notches in every ring; no corner joints to show. The lid is two layers, closed or slid half open on the velvet and the rose inside. It can stand on a stone plinth. Assembly: stand the keys in the floor, thread the rings down over them, glue each, lay the lid on; set it all on the plinth.

Library Bookcase
PersonalizzabileGratis
Taglio laserStampa 3D
di Kerf Designs

Library Bookcase

A miniature for book nooks and dioramas. Library bookcase: a miniature bookcase with its rolling-style ladder, for dioramas, dollhouses and book nooks. The bookcase is a tab-and-slot box of sides, a back, shelves and a top, with rows of books standing in slots on every shelf and, with the ladder, a brass rail tabbed across the front. The ladder's two rails lean back to that rail and hook over it through notches in their tops; its treads tab into the rails and its feet stand in the base. One book on the top shelf has a ribbon bookmark with an initial on it. Assembly: build the bookcase and stan

Bread Rack
PersonalizzabileGratis
Taglio laserStampa 3D
di Kerf Designs

Bread Rack

A miniature for book nooks and dioramas. Bread rack: a miniature bakery rack for dioramas, shop fronts and book nooks. Two ladder ends (legs, a band at every shelf, cut-outs between) hold slatted shelves tabbed into them, and the bread stands in slots on the shelves: round loaves, croissants, and baguettes in a basket on top. Assembly: push the shelves into one ladder end, add the other, stand the bread in its slots, set the feet in the base.

Design simili

Flag
PersonalizzabileGratis
Taglio laserStampa 3D
di Kerf Designs

Flag

A miniature for book nooks and dioramas. Pride flag on its stand: a desk flag for your desk or shelf, or a miniature for a book nook. The pole and the flag are cut in one and stand in a base that reaches under the flag. The engraved finish uses scored stripes and selective hatching. For colour finishes, glue the Progress flag's chevrons or the Intersex flag's ring onto the flag.

Loop Clamps
PersonalizzabileGratis
Stampa 3D
di Hardware Designs

Loop Clamps

P-shaped loop clamps for cable bundles, hoses, tubes and pipes, from 3 mm cords to 50 mm hoses. The strap wraps once and both ends meet in a double tab, so the screw pulls the loop closed. Prints flat with no supports. Turn on the assortment to print a whole run of sizes on one plate.

Sticky Note Caddy
PersonalizzabileGratis
Taglio laserStampa 3D
di Kerf Designs

Sticky Note Caddy

Sticky note caddy: a desk block built up in layers, with a well for each pad of sticky notes and a taller tower of pen holes at the end. The wells are sized to your pads, with a dip at the front to lift the last sheets out, and the layers step up where the pens need depth. Your name is engraved on the top. Assembly: glue the layers in order, base first, lining up the edges.

Snap-In Cable Bushings
PersonalizzabileGratis
Stampa 3D
di Hardware Designs

Snap-In Cable Bushings

Strain relief bushings that snap into a hole in a panel, enclosure or laser-cut box and keep the cable off the cut edge. Size it to the cable and panel thickness, with room for up to three cables side by side. Prints flange down with no supports. Push it through until the fingers click behind the panel.