Indietro: Community
MyLaserTools.com

Four in a Row

Four in a row: drop your tokens into the columns and be first to line up four, across, up or diagonally. The board is two face plates held apart by the column…

di Kerf Designs

Impostazioni

Unità

Board

Columns
Columns
Rows
Rows
Token
Token diameter

Assembled view

Drop
How far the last token has dropped, 0 to 1

Material

Spessore del materiale
Il foglio che tagli. Fessure e linguette si adeguano.
mm
Kerf
Quanto materiale il laser brucia via.
mm
Clearance

Anteprima 3D

Generazione del modello
Palette di ispirazione

Codice

Copia nel Banco di lavoro

Foto

Four in a Row

Informazioni su questo design

Taglio laser e Stampa 3D

Four in a row: drop your tokens into the columns and be first to line up four, across, up or diagonally. The board is two face plates held apart by the column separators, whose tabs pass through both plates and are glued, so the board stays square and flat. It slides into the two stands, and pulling the release bar out at the bottom lets all the tokens fall out to start again. One player's tokens are walnut, the other's plywood. Assembly: glue the separators' tabs into one face plate, lay the release bar along the bottom without glue, and glue the other plate on, checking the bar still slides.

BambiniPuzzle e GiochiGiocattoli
gamestoyskids

Uso personaleUso commerciale

Che cosa significa?

Come realizzarlo

  1. 1Cambia le impostazioni. L'anteprima si aggiorna a ogni modifica.
  2. 2Scarica l'SVG per il tuo laser, oppure aprilo nell'Editor di design per aggiungerci altro.
  3. 3Metti Mi piace al design e aggiungi qui sotto una foto di quello che hai realizzato.

Domande

Sì. È gratuito da scaricare e da usare secondo la sua licenza.

Sì. Cambia le impostazioni in questa pagina e l'anteprima si aggiorna mentre lavori. Quando ti convince, scarica il file.

Un SVG per il software del tuo laser. Puoi anche aprirlo nell'Editor di design, oppure scaricare STL e 3MF allo spessore del materiale per stampare i pezzi.

La dimensione segue le impostazioni di questa pagina, e il riquadro delle misure sotto l'anteprima mostra il risultato.

Imposta lo spessore del materiale uguale a quello del foglio che tagli. Linguette e fessure si adeguano.

Sì. La licenza copre l'uso personale e commerciale dei pezzi che realizzi.

Realizzato dalla community

Lo hai tagliato? Condividi una foto e una nota su come è andata e ricevi subito 10 scintille.

L'ho realizzato

Altri di Kerf Designs

Locker Stall
PersonalizzabileGratis
Taglio laserStampa 3D
di Kerf Designs

Locker Stall

A miniature for book nooks and dioramas. Locker stall: a miniature team locker with the player's jersey, for dioramas, shelves and a gift to any player. Two sides hold the back, a kick panel, a bench seat, a helmet shelf and a name board, all tabbed in; the jersey (team colours, name, number) hangs by a hole in its hanger on a peg tabbed into the back. Skates or cleats can stand on the seat, the helmet on the shelf. Hockey, soccer, basketball or baseball. Assembly: push the back, the kick panel, the seat, the shelf and the name board into one side, add the other, push the peg into the back, ha

Vampire Coffin
PersonalizzabileGratis
Taglio laserStampa 3D
di Kerf Designs

Vampire Coffin

A miniature for book nooks and dioramas. Coffin: a miniature vampire's coffin for dioramas, Halloween and book nooks. A true coffin shape from every side: a stack of coffin-shaped rings on a solid floor, aligned by two keys that stand in the floor's slots and slide through notches in every ring; no corner joints to show. The lid is two layers, closed or slid half open on the velvet and the rose inside. It can stand on a stone plinth. Assembly: stand the keys in the floor, thread the rings down over them, glue each, lay the lid on; set it all on the plinth.

Library Bookcase
PersonalizzabileGratis
Taglio laserStampa 3D
di Kerf Designs

Library Bookcase

A miniature for book nooks and dioramas. Library bookcase: a miniature bookcase with its rolling-style ladder, for dioramas, dollhouses and book nooks. The bookcase is a tab-and-slot box of sides, a back, shelves and a top, with rows of books standing in slots on every shelf and, with the ladder, a brass rail tabbed across the front. The ladder's two rails lean back to that rail and hook over it through notches in their tops; its treads tab into the rails and its feet stand in the base. One book on the top shelf has a ribbon bookmark with an initial on it. Assembly: build the bookcase and stan

Bread Rack
PersonalizzabileGratis
Taglio laserStampa 3D
di Kerf Designs

Bread Rack

A miniature for book nooks and dioramas. Bread rack: a miniature bakery rack for dioramas, shop fronts and book nooks. Two ladder ends (legs, a band at every shelf, cut-outs between) hold slatted shelves tabbed into them, and the bread stands in slots on the shelves: round loaves, croissants, and baguettes in a basket on top. Assembly: push the shelves into one ladder end, add the other, stand the bread in its slots, set the feet in the base.

Design simili

Grandmother's Canopy Bed
PersonalizzabileGratis
Taglio laserStampa 3D
di Kerf Designs

Grandmother's Canopy Bed

A miniature for book nooks and dioramas. Six selected-stock parts form an empty bed with integral tied curtains.

Table Corner Guards
PersonalizzabileGratis
Stampa 3D
di Hardware Designs

Table Corner Guards

Rounded covers for sharp table, desk, shelf and hearth corners, sized to the thickness of the top. Use double-sided tape, or turn on the lip that hooks under the edge. Prints upside down with no supports. TPU gives a softer bump.

Forty-Layer Bed
PersonalizzabileGratis
Taglio laserStampa 3D
di Kerf Designs

Forty-Layer Bed

A miniature for book nooks and dioramas. Twenty mattresses, twenty eiderdowns and a pea under the bottom layer. Assemble boards around deck and rails, then key the frame into its base. Seat bearers and reveal, glue two 2.5 mm pins into the foundation only, and slide the 39 bored bedding plates down them. Fit the assembled ladder into its base, then close both ladder heads with the last 1.5 mm quilt.

Spindle Bench
PersonalizzabileGratis
Taglio laserStampa 3D
di Kerf Designs

Spindle Bench

A miniature for book nooks and dioramas. A parked hardwood spindle threads through the bench's cheeks and whorl. Glue the shaft into both cheeks and all three whorl courses.