# Making a laser cut lunar calendar

> a moon phase wheel for any year, with a top disc that turns to today

A lunar calendar is a year laid out as a circle. January starts at the top and the days run clockwise, so the moon phases sit around the ring in the order they happen. Turn the pointer to today and you can see how far it is to the next **full moon**.

The generator works out every phase to the minute and then places it on the date for your **time zone**. That matters more than it sounds: a full moon at half past midnight in Paris is still the previous evening in New York, and the icon belongs on a different day.

## What you need

### Materials

- **Discs:** 3 mm birch plywood. A pale wood shows the small engraved numbers best.
- **Split pin:** a 4 mm split pin, paper fastener or short rivet for the centre. Not needed for the flat wheel.
- **Masking tape** on the face before engraving, if your laser leaves smoke marks.

## 1. Pick how it turns



- **Window disc** puts a large top disc over the phase ring. Its pointer marks the day and a window shows the two or three phases around it.
- **Pointer arm** glues a smaller top disc to the base and adds a thin arm that turns over everything, so the whole year stays visible.
- **Flat wheel** is one disc with the artwork in the middle and no moving parts.

![A window disc and a pointer arm lunar calendar side by side](https://www.mylasertools.com/tool-previews/lunar-calendar-generator.webp)

The window disc on the left and the pointer arm on the right, as the generator previews them.

## 2. Set the year, time zone and hemisphere



Type the **year** and pick the **time zone** where the calendar will hang. The counter under the settings tells you how many phases fall in that year, usually 49 or 50. South of the equator, switch **Hemisphere** to Southern so the first and last quarter icons are lit from the correct side.

## 3. Size it



**Diameter** sets the whole wheel. The hint under it shows how tall the smallest text will be; keep it above 2 mm or they blur on wood. 200 mm is a good size for a desk or a wall. Set **Split pin hole** to your pin's shank plus a few tenths of a millimetre so the disc turns without wobbling.

## 4. Write on the top disc



Choose **Celestial**, **Minimal** or **Botanical**, then change the title and the personal message. All text is engraved with a single line font, which is one pass of the laser instead of a filled outline. If the font is missing a letter you typed, the generator says so and you can try another font.

## 5. Check the assembled view and export



The **Assembled** tab shows the discs stacked and turned to a date you pick. When it looks right, download the SVG. If the sheet is bigger than your laser bed, use **Part to export** to save one disc at a time.

## Laser cutting

### What to cut and engrave



- **Fill engrave** the blue layer: the moon phase icons, the big crescent and the leaves.
- **Line engrave** the teal layer: day ticks, numbers, month names, rings and all the text. Use a fast, low power line setting.
- **Cut** the red layer last: the disc outlines, the window, the pointer and the pin holes.

### Put it together



1. Peel the tape and wipe the discs with a barely damp cloth.
2. Lay the top disc on the base with the pointer up, push the split pin through both centre holes and open its legs flat at the back.
3. For the pointer arm build, glue the small top disc to the base first, then pin the arm on top.
4. Turn the pointer to today. Check one phase against a moon app to be sure the time zone is right.

## Make it yours

- Cut the top disc from a darker wood, like walnut, so it stands out from the base.
- Put a birth date or anniversary in the message and give the calendar for that year as a gift.
- Use the hanging tab and a brass pin for a wall version, or glue a small stand behind a flat wheel.

---

Open the Lunar Calendar Generator: https://www.mylasertools.com/lunar-calendar-generator
Read online: https://www.mylasertools.com/learn/guides/lunar-calendar-generator
