# How to make layered wall art panels

> stacked pattern sheets that close in toward the back, mandalas and optical illusions

A layered wall panel is a few flat sheets cut from the same pattern and glued in a stack. The front sheet has thin bars and big openings. Each sheet behind it has wider bars, so the openings step in toward the back and the panel gets depth without any carving.

The photo shows two finished panels: a Vega Grid optical illusion that bulges into a sphere, and a Sunburst stacked in white and yellow behind it.

## What you need

- 3 mm sheet material for every layer: [TruFlat White Plywood](https://yxecreations.com/products/truflat%C2%AE-white-plywood-2-0) for the front and [cast acrylic](https://yxecreations.com/pages/acrylic-sheets) or more plywood for the sheets behind it.
- Wood glue for plywood, or a clear acrylic adhesive for acrylic sheets.
- Clamps or a few heavy books to keep the stack flat while the glue sets.
- A sawtooth hanger or adhesive strips for the wall.

## 1. Pick a pattern



Open **Pattern** and choose a layered design, a mandala, an optical illusion or any tile from the pattern library. The thumbnails show the stack with your current settings. **Pattern size** makes the repeat bigger or smaller, and patterns with a random layout, such as Voronoi, get a **New random layout** button.

## 2. Set the sheets and the layer step



- **Sheets** sets how many layers the panel has, from 2 to 8. Sheet 1 is the back.
- **Layer step** is how much wider the bars get on each side, per sheet going back. Set it to 0 to cut every sheet the same, for example to stack several sheets of thin material into one thick panel.
- **Bar width** sets the strips on the front sheet, and **Smallest opening** fills in gaps too narrow to cut cleanly.
- If the sheet list warns that the back sheets have almost no openings left, lower the layer step or the bar width, or make the pattern bigger.

![Three-layer floral wall panel with a white plywood front over orange and yellow acrylic sheets](https://www.mylasertools.com/tool-previews/layered-wall-art-generator.webp)

Three sheets: a white plywood front over orange and yellow acrylic. The colour steps back toward the middle.

## 3. Change the sheets underneath



Under **Lower sheets**, **Aligned** keeps every sheet lined up. **Rotate**, **Zoom** and **Spin** turn or scale the pattern on each sheet further back, so the layers stop lining up and the panel looks twisted or deep. **Mix in a second pattern** uses a second design on every other sheet behind the front.

## 4. Shape the panel



Choose a **Square**, **Round** or **Rectangle** panel, set the size and the **Frame width**. The **Back sheet** can be **Solid** to close the panel, or **Patterned** to let light through for a lightbox.

## 5. Download the sheets



**Download SVG** puts every sheet in one file. The sheet list under the preview downloads one sheet at a time, which is handy when each sheet is a different material. **Open in Design Editor** takes the sheets into the editor for more changes.

## Laser Cutting

### Cut and glue the stack



1. Measure your sheet with calipers and set **Sheet thickness**, so the 3D preview matches the real stack.
2. Cut each sheet from its own material. Cut the inner openings before the outer edge if your software lets you order cuts, so the sheet does not shift.
3. Lay sheet 1, the back, face down first. Spread a thin layer of glue on the bars only, so it does not squeeze into the openings.
4. Stack the rest on top in order with the edges lined up, then clamp or weigh the panel flat until the glue sets.

## Make it yours

Try an optical illusion such as Vega Grid in a single wood-grain sheet over a darker back, or a mandala in three colours of acrylic. A patterned back sheet with an LED panel behind it turns the panel into a lightbox.

---

Open the Layered Wall Art Generator: https://www.mylasertools.com/layered-wall-art-generator
Read online: https://www.mylasertools.com/learn/guides/layered-wall-art-generator