Volver: Comunidad
MyLaserTools.com

Helix Archimedes screw marble lift

Helix: an Archimedes screw marble lift. Turn the crank and a screw of 120 stacked plates, each a step round from the last on a square bar, pushes 16 mm…

por Kerf Designs

Configuración

Screw

Flight
Plates the flight tooth spans: two leaves a longer pocket, three is stronger
Crank radius
Crank handle radius

Fit

Bar clearance
Added to the 10 mm square bar in every star-shaped hole
Bearing clearance
Added to the 20 mm journals in the end plate bearings

Assembly

Crank angle
turn lifts every marble one pitch

Export

Output
All parts, or one group at a time

Material

Grosor del material
Sheet thickness
Kerf
Beam width

Vista previa 3D

Creando tu modelo
Paleta inspiracional

Código

Copiar al Banco de trabajo

Fotos

Helix Archimedes screw marble lift

Sobre este diseño

Corte láser e Impresión 3D

Helix: an Archimedes screw marble lift. Turn the crank and a screw of 120 stacked plates, each a step round from the last on a square bar, pushes 16 mm marbles up a trough of dowels. At the top they drop onto a chute and roll back down a zig-zag track behind the screw to a ramp that feeds the screw again near the bottom.

NiñosMaquetasJuguetes
marble machinesmechanisms

Uso personalUso comercial

¿Qué significa esto?

Cómo hacerlo

  1. 1Cambia los ajustes. La vista previa se actualiza tras cada cambio.
  2. 2Descarga el SVG para tu láser o ábrelo en el Editor de diseños para añadirle más cosas.
  3. 3Dale me gusta al diseño y añade abajo una foto de lo que hiciste.

Preguntas

Sí. Puedes descargarlo y usarlo gratis según su licencia.

Sí. Cambia los ajustes en esta página y la vista previa se actualiza al momento. Cuando te guste, descarga el archivo.

Un SVG para tu software láser. También puedes abrirlo en el Editor de diseños o descargar STL y 3MF con el grosor del material para imprimir las piezas.

El tamaño depende de los ajustes de esta página, y el recuadro de tamaño bajo la vista previa muestra el resultado.

Ajusta el grosor del material a la plancha que cortas. Las ranuras y pestañas se adaptan a él.

Sí. La licencia cubre el uso personal y comercial de las piezas que hagas.

Hecho por la comunidad

¿Lo cortaste? Comparte una foto y una nota sobre cómo salió y recibe 10 chispas al instante.

Lo hice

Más de Kerf Designs

Locker Stall
PersonalizableGratis
Corte láserImpresión 3D
por Kerf Designs

Locker Stall

A miniature for book nooks and dioramas. Locker stall: a miniature team locker with the player's jersey, for dioramas, shelves and a gift to any player. Two sides hold the back, a kick panel, a bench seat, a helmet shelf and a name board, all tabbed in; the jersey (team colours, name, number) hangs by a hole in its hanger on a peg tabbed into the back. Skates or cleats can stand on the seat, the helmet on the shelf. Hockey, soccer, basketball or baseball. Assembly: push the back, the kick panel, the seat, the shelf and the name board into one side, add the other, push the peg into the back, ha

Vampire Coffin
PersonalizableGratis
Corte láserImpresión 3D
por Kerf Designs

Vampire Coffin

A miniature for book nooks and dioramas. Coffin: a miniature vampire's coffin for dioramas, Halloween and book nooks. A true coffin shape from every side: a stack of coffin-shaped rings on a solid floor, aligned by two keys that stand in the floor's slots and slide through notches in every ring; no corner joints to show. The lid is two layers, closed or slid half open on the velvet and the rose inside. It can stand on a stone plinth. Assembly: stand the keys in the floor, thread the rings down over them, glue each, lay the lid on; set it all on the plinth.

Library Bookcase
PersonalizableGratis
Corte láserImpresión 3D
por Kerf Designs

Library Bookcase

A miniature for book nooks and dioramas. Library bookcase: a miniature bookcase with its rolling-style ladder, for dioramas, dollhouses and book nooks. The bookcase is a tab-and-slot box of sides, a back, shelves and a top, with rows of books standing in slots on every shelf and, with the ladder, a brass rail tabbed across the front. The ladder's two rails lean back to that rail and hook over it through notches in their tops; its treads tab into the rails and its feet stand in the base. One book on the top shelf has a ribbon bookmark with an initial on it. Assembly: build the bookcase and stan

Bread Rack
PersonalizableGratis
Corte láserImpresión 3D
por Kerf Designs

Bread Rack

A miniature for book nooks and dioramas. Bread rack: a miniature bakery rack for dioramas, shop fronts and book nooks. Two ladder ends (legs, a band at every shelf, cut-outs between) hold slatted shelves tabbed into them, and the bread stands in slots on the shelves: round loaves, croissants, and baguettes in a basket on top. Assembly: push the shelves into one ladder end, add the other, stand the bread in its slots, set the feet in the base.

Diseños parecidos

Grandmother's Canopy Bed
PersonalizableGratis
Corte láserImpresión 3D
por Kerf Designs

Grandmother's Canopy Bed

A miniature for book nooks and dioramas. Six selected-stock parts form an empty bed with integral tied curtains.

Table Corner Guards
PersonalizableGratis
Impresión 3D
por Hardware Designs

Table Corner Guards

Rounded covers for sharp table, desk, shelf and hearth corners, sized to the thickness of the top. Use double-sided tape, or turn on the lip that hooks under the edge. Prints upside down with no supports. TPU gives a softer bump.

Forty-Layer Bed
PersonalizableGratis
Corte láserImpresión 3D
por Kerf Designs

Forty-Layer Bed

A miniature for book nooks and dioramas. Twenty mattresses, twenty eiderdowns and a pea under the bottom layer. Assemble boards around deck and rails, then key the frame into its base. Seat bearers and reveal, glue two 2.5 mm pins into the foundation only, and slide the 39 bored bedding plates down them. Fit the assembled ladder into its base, then close both ladder heads with the last 1.5 mm quilt.

Spindle Bench
PersonalizableGratis
Corte láserImpresión 3D
por Kerf Designs

Spindle Bench

A miniature for book nooks and dioramas. A parked hardwood spindle threads through the bench's cheeks and whorl. Glue the shaft into both cheeks and all three whorl courses.