Volver: Comunidad
MyLaserTools.com

Fractal tree ornament

Fractal tree: a module that calls itself. Each branch splits in two, a little shorter and thinner, until the twigs end in leaves. The seed bends every branch…

por Kerf Designs

Configuración

Unidades

Tree

Size
Diameter of the ring
Depth
How many times the branches split
Spread
Angle between two branches, in degrees
Ratio
Length of a branch compared with the one before
Wildness
How much the branches wander
Seed
Different seeds grow different trees
Leaves
Round leaves at the ends of the twigs

Text

Label
Engraved on the ground, leave empty for none

Material

Grosor del material
Sheet thickness
mm
Kerf
Beam width
mm

Vista previa 3D

Creando tu modelo
Paleta inspiracional

Código

Copiar al Banco de trabajo

Fotos

Fractal tree ornament

Sobre este diseño

Corte láser e Impresión 3D

Fractal tree: a module that calls itself. Each branch splits in two, a little shorter and thinner, until the twigs end in leaves. The seed bends every branch differently, so no two trees are the same.

NavidadAdornos
ornamentschristmas

Uso personalUso comercial

¿Qué significa esto?

Cómo hacerlo

  1. 1Cambia los ajustes. La vista previa se actualiza tras cada cambio.
  2. 2Descarga el SVG para tu láser o ábrelo en el Editor de diseños para añadirle más cosas.
  3. 3Dale me gusta al diseño y añade abajo una foto de lo que hiciste.

Preguntas

Sí. Puedes descargarlo y usarlo gratis según su licencia.

Sí. Cambia los ajustes en esta página y la vista previa se actualiza al momento. Cuando te guste, descarga el archivo.

Un SVG para tu software láser. También puedes abrirlo en el Editor de diseños o descargar STL y 3MF con el grosor del material para imprimir las piezas.

El tamaño depende de los ajustes de esta página, y el recuadro de tamaño bajo la vista previa muestra el resultado.

Ajusta el grosor del material a la plancha que cortas. Las ranuras y pestañas se adaptan a él.

Sí. La licencia cubre el uso personal y comercial de las piezas que hagas.

Hecho por la comunidad

¿Lo cortaste? Comparte una foto y una nota sobre cómo salió y recibe 10 chispas al instante.

Lo hice

Más de Kerf Designs

Locker Stall
PersonalizableGratis
Corte láserImpresión 3D
por Kerf Designs

Locker Stall

A miniature for book nooks and dioramas. Locker stall: a miniature team locker with the player's jersey, for dioramas, shelves and a gift to any player. Two sides hold the back, a kick panel, a bench seat, a helmet shelf and a name board, all tabbed in; the jersey (team colours, name, number) hangs by a hole in its hanger on a peg tabbed into the back. Skates or cleats can stand on the seat, the helmet on the shelf. Hockey, soccer, basketball or baseball. Assembly: push the back, the kick panel, the seat, the shelf and the name board into one side, add the other, push the peg into the back, ha

Vampire Coffin
PersonalizableGratis
Corte láserImpresión 3D
por Kerf Designs

Vampire Coffin

A miniature for book nooks and dioramas. Coffin: a miniature vampire's coffin for dioramas, Halloween and book nooks. A true coffin shape from every side: a stack of coffin-shaped rings on a solid floor, aligned by two keys that stand in the floor's slots and slide through notches in every ring; no corner joints to show. The lid is two layers, closed or slid half open on the velvet and the rose inside. It can stand on a stone plinth. Assembly: stand the keys in the floor, thread the rings down over them, glue each, lay the lid on; set it all on the plinth.

Library Bookcase
PersonalizableGratis
Corte láserImpresión 3D
por Kerf Designs

Library Bookcase

A miniature for book nooks and dioramas. Library bookcase: a miniature bookcase with its rolling-style ladder, for dioramas, dollhouses and book nooks. The bookcase is a tab-and-slot box of sides, a back, shelves and a top, with rows of books standing in slots on every shelf and, with the ladder, a brass rail tabbed across the front. The ladder's two rails lean back to that rail and hook over it through notches in their tops; its treads tab into the rails and its feet stand in the base. One book on the top shelf has a ribbon bookmark with an initial on it. Assembly: build the bookcase and stan

Bread Rack
PersonalizableGratis
Corte láserImpresión 3D
por Kerf Designs

Bread Rack

A miniature for book nooks and dioramas. Bread rack: a miniature bakery rack for dioramas, shop fronts and book nooks. Two ladder ends (legs, a band at every shelf, cut-outs between) hold slatted shelves tabbed into them, and the bread stands in slots on the shelves: round loaves, croissants, and baguettes in a basket on top. Assembly: push the shelves into one ladder end, add the other, stand the bread in its slots, set the feet in the base.

Diseños parecidos

Marley's Chain and Cash-Box
PersonalizableGratis
Corte láserImpresión 3D
por Kerf Designs

Marley's Chain and Cash-Box

A miniature for book nooks and dioramas. Hold the closed links parallel. Slide each open C half in from its own side, then glue the layers together along their offset seams.

Scrooge's Counting House Book Nook
PersonalizableGratis
Corte láserImpresión 3D
por Kerf Designs

Scrooge's Counting House Book Nook

A cold Christmas Eve in the counting house, with the chain from Scrooge's lodgings worked into the open doorway as a story clue.

Word Ornament
PersonalizableGratis
Corte láserImpresión 3D
por Kerf Designs

Word Ornament

Word ornament: a word for the tree or a window, like JOY or NOEL, cut as one piece. The letters stand on a bar whose ends curl up into loops, and an arch springs from loop to loop over the word with a star at its top to hang it by. The arch is worked out to clear the tops of the letters, so it never cuts into one, and the letters are sized to the word, so any word fits the same width. Assembly: tie a ribbon through the hole in the star.

Guitar Ornament
PersonalizableGratis
Corte láserImpresión 3D
por Kerf Designs

Guitar Ornament

Guitar ornament: a little guitar for a musician's tree or a gift tag, with a name across the body. Two layers: the back is the whole silhouette, and the top has the sound hole cut through so the back shows dark inside it, with the bridge, frets and strings scored and engraved. Acoustic or electric, any size. Assembly: glue the top onto the back and tie a ribbon through the headstock.