Volver: Comunidad
MyLaserTools.com

The Laboratory Book Nook

Ingolstadt. The rain persists after Victor has left his workshop. The brass pins run through both cheeks and both rails. To remove the table, shift it about 7…

por Kerf Designs

Configuración

Theme

Name
Raised
Drain detail
Finish
How the details are cut: engraved, shaded in three engrave depths, or left plain

Size

Width
Outside width in millimetres
Depth
Outside depth in millimetres
Height
Outside height in millimetres
Scale to
Scale of the scene: 1 to this number

Material

Grosor del material
Sheet thickness in millimetres
Fine
Thickness of the thin detail sheet in millimetres
Kerf
Laser kerf in millimetres
Clearance
Extra gap in the joints, in millimetres

Vista previa 3D

Creando tu modelo
Paleta inspiracional

Código

Copiar al Banco de trabajo

Fotos

The Laboratory Book Nook

Sobre este diseño

Corte láser e Impresión 3D

Ingolstadt. The rain persists after Victor has left his workshop. The brass pins run through both cheeks and both rails. To remove the table, shift it about 7 mm toward the aisle, lift it over the front sill and slide it forward. Draw the aft pin only once the table is outside.

Amantes de los librosHalloweenDecoración para el hogarMiniaturas
book nooksdioramasminiatures

Uso personalUso comercial

¿Qué significa esto?

Cómo hacerlo

  1. 1Cambia los ajustes. La vista previa se actualiza tras cada cambio.
  2. 2Descarga el SVG para tu láser o ábrelo en el Editor de diseños para añadirle más cosas.
  3. 3Dale me gusta al diseño y añade abajo una foto de lo que hiciste.

Preguntas

Sí. Puedes descargarlo y usarlo gratis según su licencia.

Sí. Cambia los ajustes en esta página y la vista previa se actualiza al momento. Cuando te guste, descarga el archivo.

Un SVG para tu software láser. También puedes abrirlo en el Editor de diseños o descargar STL y 3MF con el grosor del material para imprimir las piezas.

El tamaño depende de los ajustes de esta página, y el recuadro de tamaño bajo la vista previa muestra el resultado.

Ajusta el grosor del material a la plancha que cortas. Las ranuras y pestañas se adaptan a él.

Sí. La licencia cubre el uso personal y comercial de las piezas que hagas.

Hecho por la comunidad

¿Lo cortaste? Comparte una foto y una nota sobre cómo salió y recibe 10 chispas al instante.

Lo hice

Más de Kerf Designs

Locker Stall
PersonalizableGratis
Corte láserImpresión 3D
por Kerf Designs

Locker Stall

A miniature for book nooks and dioramas. Locker stall: a miniature team locker with the player's jersey, for dioramas, shelves and a gift to any player. Two sides hold the back, a kick panel, a bench seat, a helmet shelf and a name board, all tabbed in; the jersey (team colours, name, number) hangs by a hole in its hanger on a peg tabbed into the back. Skates or cleats can stand on the seat, the helmet on the shelf. Hockey, soccer, basketball or baseball. Assembly: push the back, the kick panel, the seat, the shelf and the name board into one side, add the other, push the peg into the back, ha

Vampire Coffin
PersonalizableGratis
Corte láserImpresión 3D
por Kerf Designs

Vampire Coffin

A miniature for book nooks and dioramas. Coffin: a miniature vampire's coffin for dioramas, Halloween and book nooks. A true coffin shape from every side: a stack of coffin-shaped rings on a solid floor, aligned by two keys that stand in the floor's slots and slide through notches in every ring; no corner joints to show. The lid is two layers, closed or slid half open on the velvet and the rose inside. It can stand on a stone plinth. Assembly: stand the keys in the floor, thread the rings down over them, glue each, lay the lid on; set it all on the plinth.

Library Bookcase
PersonalizableGratis
Corte láserImpresión 3D
por Kerf Designs

Library Bookcase

A miniature for book nooks and dioramas. Library bookcase: a miniature bookcase with its rolling-style ladder, for dioramas, dollhouses and book nooks. The bookcase is a tab-and-slot box of sides, a back, shelves and a top, with rows of books standing in slots on every shelf and, with the ladder, a brass rail tabbed across the front. The ladder's two rails lean back to that rail and hook over it through notches in their tops; its treads tab into the rails and its feet stand in the base. One book on the top shelf has a ribbon bookmark with an initial on it. Assembly: build the bookcase and stan

Bread Rack
PersonalizableGratis
Corte láserImpresión 3D
por Kerf Designs

Bread Rack

A miniature for book nooks and dioramas. Bread rack: a miniature bakery rack for dioramas, shop fronts and book nooks. Two ladder ends (legs, a band at every shelf, cut-outs between) hold slatted shelves tabbed into them, and the bread stands in slots on the shelves: round loaves, croissants, and baguettes in a basket on top. Assembly: push the shelves into one ladder end, add the other, stand the bread in its slots, set the feet in the base.

Diseños parecidos

Rowing Boat
PersonalizableGratis
Corte láserImpresión 3D
por Kerf Designs

Rowing Boat

A miniature for book nooks and dioramas. Four glued hull courses, two thwarts, a name deck and two oars. Every part uses the selected plywood thickness. Glue the oars to the thwarts.

Grandmother's Canopy Bed
PersonalizableGratis
Corte láserImpresión 3D
por Kerf Designs

Grandmother's Canopy Bed

A miniature for book nooks and dioramas. Six selected-stock parts form an empty bed with integral tied curtains.

Forty-Layer Bed
PersonalizableGratis
Corte láserImpresión 3D
por Kerf Designs

Forty-Layer Bed

A miniature for book nooks and dioramas. Twenty mattresses, twenty eiderdowns and a pea under the bottom layer. Assemble boards around deck and rails, then key the frame into its base. Seat bearers and reveal, glue two 2.5 mm pins into the foundation only, and slide the 39 bored bedding plates down them. Fit the assembled ladder into its base, then close both ladder heads with the last 1.5 mm quilt.

Spindle Bench
PersonalizableGratis
Corte láserImpresión 3D
por Kerf Designs

Spindle Bench

A miniature for book nooks and dioramas. A parked hardwood spindle threads through the bench's cheeks and whorl. Glue the shaft into both cheeks and all three whorl courses.