Volver: Comunidad
MyLaserTools.com

Loop Clamps

P-shaped loop clamps for cable bundles, hoses, tubes and pipes, from 3 mm cords to 50 mm hoses. The strap wraps once and both ends meet in a double tab, so…

por Hardware Designs

Configuración

Clamp

Loop
Inside diameter of the loop in mm
Assortment
Print a run of sizes from 3 mm up to this loop size
Thickness
Strap thickness in mm
Width
Clamp width in mm

Tab

Tab
Tab length in mm
Screw
Screw hole diameter in mm

Vista previa 3D

Creando tu modelo
Paleta inspiracional

Código

Copiar al Banco de trabajo

Fotos

Loop Clamps

Sobre este diseño

Escrito en OpenSCAD · Impresión 3D

P-shaped loop clamps for cable bundles, hoses, tubes and pipes, from 3 mm cords to 50 mm hoses. The strap wraps once and both ends meet in a double tab, so the screw pulls the loop closed.

Prints flat with no supports. Turn on the assortment to print a whole run of sizes on one plate.

Exclusivo para impresión 3DEscritorio y oficinaFerretería
cable clampp cliphosecable management

Uso personalUso comercial

¿Qué significa esto?

Cómo hacerlo

  1. 1Cambia los ajustes. La vista previa se actualiza tras cada cambio.
  2. 2Descarga STL para cualquier laminador, o 3MF para mantener separadas las piezas de color.
  3. 3Dale me gusta al diseño y añade abajo una foto de lo que hiciste.

Preguntas

Sí. Puedes descargarlo y usarlo gratis según su licencia.

Sí. Cambia los ajustes en esta página y la vista previa se actualiza al momento. Cuando te guste, descarga el archivo.

STL para cualquier laminador y 3MF con cada pieza de color como un objeto aparte.

El tamaño depende de los ajustes de esta página, y el recuadro de tamaño bajo la vista previa muestra el resultado.

Sí. La licencia cubre el uso personal y comercial de las piezas que hagas.

Hecho por la comunidad

¿Lo cortaste? Comparte una foto y una nota sobre cómo salió y recibe 10 chispas al instante.

Lo hice

Más de Hardware Designs

Crank Handle
PersonalizableGratis
Impresión 3D
por Hardware Designs

Crank Handle

A hand crank with a square, hex, round or D bore and a grip that spins on its pin. For awning winders, pasta rollers, window cranks, winches and anything with an adjusting screw. The arm prints flat and the grip prints upright, then snaps onto the pin. A pointed set screw hole holds it on the shaft.

Flanged and Cap Nuts
PersonalizableGratis
Impresión 3D
por Hardware Designs

Flanged and Cap Nuts

Printed hex nuts with a washer flange that spreads the load on wood and plastic, or a domed cap that covers the sharp end of the bolt. Metric and UNC sizes, with a clearance setting so the thread suits your printer. Prints upright with no supports, several at once.

Lever Handle Nut
PersonalizableGratis
Impresión 3D
por Hardware Designs

Lever Handle Nut

A clamping lever for router fences, drill press tables, tool rests and camera rigs, where a round knob slips in your hand. Straight, cranked or paddle lever, 35 to 140 mm long. Use a printed thread, a pocket for a steel nut, or a bolt head pocket. Prints flat with no supports.

Wing and Thumb Nuts
PersonalizableGratis
Impresión 3D
por Hardware Designs

Wing and Thumb Nuts

Hand-tightened nuts for M5 to M12 and 1/4 to 1/2 inch bolts, in wing, big wing, knurled, star and lobed shapes. Pick a printed thread, a pocket that grips a steel nut, or a pocket for a bolt head to turn it into a thumb screw. Prints upright with no supports. Printed threads hold best from M6 and 1/4 inch up; below that use the steel nut pocket.

Diseños parecidos

Turnbuckle
PersonalizableGratis
Impresión 3D
por Hardware Designs

Turnbuckle

A fully printed turnbuckle with one right-hand and one left-hand eye bolt. Turning the body draws both eyes in, for tightening garden wire, shade sails, banner lines and display rigging. The left-hand eye has a notch and the left-hand end of the body has a groove, so you can tell them apart. All three parts print upright with no supports.

Strap Slides and Line Tensioners
PersonalizableGratis
Impresión 3D
por Hardware Designs

Strap Slides and Line Tensioners

Tri-glide adjusters, strap keepers and D-rings for 10 to 50 mm webbing, plus three-hole tensioners for tent guy lines and clotheslines. Everything prints flat with no supports, a sheet at a time.

Rope Cleat
PersonalizableGratis
Impresión 3D
por Hardware Designs

Rope Cleat

A horn cleat for tying off flag lines, blind cords, tarps, hammocks and garden netting with a quick figure-eight. Set the length, rope size and width, and bolt it down through both posts. Prints upright with no supports. The horns rise at 45 degrees.

Tie-Down Ring
PersonalizableGratis
Impresión 3D
por Hardware Designs

Tie-Down Ring

A folding D-ring anchor for truck beds, trailers, crates, garden netting and gym straps. The ring comes off the bed already trapped under its strap, and folds flat when you are not using it. Prints flat in place with no supports. Screw down both pads.